Introduction
This manual provides essential information for the safe and effective operation, maintenance, and troubleshooting of your JEGS 5-Gallon Portable Parts Washer. This unit is designed for cleaning and degreasing small parts using water-based solvents. Please read this manual thoroughly before initial use and retain it for future reference.
Image: The JEGS 5-Gallon Portable Parts Washer, showcasing its compact design with the lid closed and the integrated power switch on the side.
Safety Information
WARNING: Improper use can lead to serious injury or property damage. Always adhere to the following safety guidelines:
- Flammable Liquids: ONLY use water-based degreasers. Never use flammable liquids such as gasoline, kerosene, or highly volatile solvents.
- Ventilation: Operate the parts washer in a well-ventilated area to prevent the buildup of fumes.
- Personal Protective Equipment (PPE): Always wear appropriate safety glasses, gloves, and other protective gear to prevent skin and eye contact with cleaning solutions.
- Electrical Safety: Ensure the power cord and plug are in good condition. Do not operate with damaged wiring. Connect to a properly grounded outlet.
- No Smoking/Open Flames: Do not smoke or use open flames near the parts washer.
- Stability: Place the unit on a stable, level surface to prevent tipping.
- Children and Pets: Keep children and pets away from the parts washer during operation and storage.
- Solvent Level: Do not overfill. Fill to just below the level of the parts shelf.
Image: The interior of the JEGS Parts Washer with the lid open, clearly showing the warning label regarding flammable liquids and the flexible nozzle for directing solvent flow.
Setup
- Unpacking: Carefully remove all components from the packaging. Inspect the unit for any shipping damage. Report any damage to the retailer immediately.
- Placement: Choose a stable, level surface in a well-ventilated area for the parts washer. Ensure there is sufficient space around the unit for safe operation and access.
- Add Solvent: Fill the tank with a suitable water-based degreaser. The maximum solvent capacity is 3.5 gallons. Do not exceed the fill line, which is typically just below the removable parts shelf.
- Connect Power: Plug the power cord into a standard 110V/60Hz grounded electrical outlet. Ensure the power switch on the side of the unit is in the "OFF" position before plugging in.
- Position Nozzle: Adjust the flexible nozzle to your desired position for directing the flow of cleaning solution.
Image: An internal view of the JEGS Parts Washer, highlighting the pump assembly responsible for circulating the cleaning solution.
Operating Instructions
- Prepare Parts: Scrape off any heavy grease or debris from the parts before placing them in the washer. This helps prolong the life of your solvent.
- Place Parts: Place the parts to be cleaned on the removable parts shelf inside the washer.
- Activate Pump: Flip the power switch on the side of the unit to the "ON" position. The pump will begin to circulate the cleaning solution through the flexible nozzle.
- Clean Parts: Use the stream from the nozzle to wash away dirt, grease, and grime from your parts. You may use a brush (not included) to assist with stubborn deposits.
- Drain: Allow cleaned parts to drain excess solvent back into the tank before removing them.
- Turn Off: When finished, flip the power switch to the "OFF" position.
Image: The interior of the JEGS Parts Washer, showing the removable parts tray which allows for easy placement and retrieval of items during cleaning.
Maintenance
- Regular Cleaning: Periodically clean the interior of the tank and the removable parts shelf to remove sludge and debris.
- Solvent Replacement: Replace the cleaning solvent when it becomes excessively dirty or loses its effectiveness. Dispose of used solvent according to local regulations.
- Pump Filter: Check the pump intake filter (if applicable) for clogs and clean as needed to maintain optimal pump output.
- Storage: When not in use, ensure the lid is closed to prevent evaporation and contamination. Store in a dry, secure location.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Pump not operating |
|
|
| Low solvent flow |
|
|
| Unit leaking |
|
|
Specifications
| Feature | Detail |
|---|---|
| Model Number | 81526 |
| Tank Capacity | 5 Gallons |
| Solvent Capacity | 3.5 Gallons |
| Max Pump Output | 3.96 Gallons Per Minute (GPM) |
| Power Requirement | 110V/60Hz |
| Material | Heavy-Duty Steel |
| Finish | Powder Coated Black |
| Overall Dimensions (L x W x H) | 17.375 in. x 14.250 in. x 8.750 in. |
| Item Weight | 17 pounds |
| Special Feature | Portable |
Image: A JEGS Parts Washer, shown in yellow for illustrative purposes, with its key dimensions (length, width, and height) clearly indicated.
Warranty and Support
Information regarding the specific warranty period and terms for the JEGS 5-Gallon Portable Parts Washer was not available in the provided product data. For warranty claims, technical support, or to inquire about replacement parts, please contact JEGS customer service directly. Refer to the product packaging or the official JEGS website for the most current contact information.
No official product videos from the seller were found in the provided data.
