Puig 9435F Naked New Generation Sport Windshield

1. Introduction

This manual provides essential information for the proper installation, operation, and maintenance of your Puig 9435F Naked New Generation Sport Windshield. This product is specifically designed for the Suzuki GSX-S750 motorcycle models from 2017 to 2020. Please read these instructions thoroughly before proceeding with installation or use to ensure safety and optimal performance.

2. Safety Information

• Always wear appropriate personal protective equipment when working on your motorcycle.
• Ensure the motorcycle is stable and securely supported before beginning any installation.
• Do not overtighten fasteners, as this can damage components. Refer to your motorcycle's service manual for specific torque values if available.
• Regularly inspect the windshield and its mounting hardware for any signs of wear, damage, or looseness.
• If you are unsure about any part of the installation process, consult a qualified motorcycle mechanic.

3. Package Contents

Verify that all components are present before beginning installation. The package should contain:

• 1 x Puig 9435F Naked New Generation Sport Windshield
• Mounting hardware kit (brackets, screws, washers, nuts)
• Installation instructions (this document)

If any parts are missing or damaged, please contact your retailer or Puig customer support.

4. Setup and Installation

Required Tools:

• Hex key set (Allen wrenches)
• Socket wrench set
• Torque wrench (recommended)
• Soft cloth to protect surfaces

Installation Steps:

1. Prepare the Motorcycle: Park your Suzuki GSX-S750 on a level surface and ensure it is stable. Turn off the engine and remove the ignition key.
2. Identify Mounting Points: Locate the designated mounting points on your motorcycle's handlebar or headlight assembly. These are typically existing bolt locations.
3. Attach Brackets: Secure the provided mounting brackets to the motorcycle using the appropriate screws and washers from the hardware kit. Do not fully tighten at this stage.
4. Mount the Windshield: Carefully position the Puig 9435F windshield onto the attached brackets. Align the holes on the windshield with the holes on the brackets.
5. Secure the Windshield: Insert the remaining screws and washers through the windshield and into the brackets. Hand-tighten all fasteners to allow for minor adjustments.
6. Adjust Position: Adjust the windshield's angle and height to your preferred riding position, ensuring it does not interfere with steering or controls.
7. Final Tightening: Once the desired position is achieved, progressively tighten all fasteners. If using a torque wrench, refer to your motorcycle's manual or the Puig instructions for specific torque specifications. Ensure all bolts are secure but not overtightened.
8. Final Inspection: Double-check all connections to ensure they are tight and secure. Verify that the windshield is stable and does not wobble.

Image: The Puig 9435F Naked New Generation Sport Windshield, showcasing its design and fit on a motorcycle. This image illustrates the product's appearance after installation.

5. Operating Instructions

Once installed, the Puig 9435F windshield requires minimal operational input. Before each ride, perform a quick visual check:

• Ensure the windshield is securely mounted and all fasteners are tight.
• Check for any cracks or damage to the windshield material.
• Verify that your visibility through the windshield is clear and unobstructed.

The windshield is designed to deflect wind and debris, enhancing rider comfort. Adjust your riding posture as needed to optimize the wind protection provided by the windshield.

6. Maintenance

Proper maintenance will extend the life and clarity of your Puig windshield:

• Cleaning: Clean the windshield regularly using a soft cloth and mild soap and water. Avoid abrasive cleaners, harsh chemicals, or paper towels, as these can scratch the surface. Rinse thoroughly with clean water and dry with a soft, lint-free cloth.
• Inspection: Periodically inspect all mounting hardware for tightness. Vibrations from riding can cause fasteners to loosen over time. Re-tighten any loose bolts as necessary.
• Damage Check: Check the windshield for any cracks, chips, or deep scratches that could impair visibility or compromise its structural integrity. Replace the windshield if significant damage is present.

7. Troubleshooting

If you encounter issues with your Puig 9435F windshield, consider the following:

• Excessive Vibration: Ensure all mounting bolts are securely tightened. Check if the windshield is properly seated in its brackets.
• Reduced Visibility: Clean the windshield thoroughly. If scratches or hazing persist, the windshield may need replacement.
• Wind Noise/Buffeting: While the windshield is designed to reduce wind, some buffeting may occur depending on rider height and helmet type. Experiment with minor adjustments to the windshield's angle if possible, or consider aftermarket deflectors if the issue persists.
• Loose Components: Regularly check and tighten all fasteners. Apply thread-locking compound (e.g., Loctite blue) to bolts if they repeatedly come loose, ensuring it is safe for the materials involved.

8. Specifications

9. Warranty and Support

For information regarding product warranty, returns, or technical support, please refer to the documentation provided with your purchase or visit the official Puig website. Keep your proof of purchase for warranty claims.