Important Safety Information
Please read and understand all instructions before beginning installation. Failure to do so may result in electric shock, fire, or other injuries that could be hazardous or even fatal. This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
- WARNING: Risk of electric shock. Disconnect power at the main fuse or circuit breaker box before installation or servicing.
- WARNING: Risk of fire. Use only bulbs of the specified type and wattage. Do not exceed the maximum wattage indicated on the fixture.
- Consult a qualified electrician if you have any electrical questions.
- Ensure all connections are secure and properly insulated.
- Do not install this fixture in wet locations. This fixture is rated for indoor use only.
Package Contents
Carefully unpack the fixture and check that all parts are included. If any parts are missing or damaged, do not attempt to assemble or install the product. Contact customer service for assistance.
- Chandelier Fixture Body (1)
- Mounting Plate/Crossbar (1)
- Mounting Screws (2)
- Wire Nuts (3)
- Canopy (1)
- Chain (1)
- Loop (2)
- Stem/Downrod (2)
- Instruction Sheet (1)
Tools Required
The following tools are typically required for installation:
- Phillips Head Screwdriver
- Flat Head Screwdriver
- Wire Strippers
- Pliers
- Electrical Tape
- Step Ladder
- Safety Glasses
Installation Instructions
Step 1: Prepare for Installation
- Turn off the electrical power at the main fuse box or circuit breaker.
- Remove the old fixture and any existing mounting hardware.
- Carefully unpack your new fixture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.
Step 2: Mount the Fixture
- Attach the mounting plate to the outlet box using the provided mounting screws. Ensure the plate is securely fastened.
- Determine the desired hanging height for the chandelier. Adjust the chain length by removing links as needed.
- Thread the fixture wires through the chain, canopy, and stem.
- Attach one end of the chain to the fixture loop and the other end to the canopy loop.
Figure 1: Front view of the Fontayne Six-Light Chandelier. This image shows the overall design with the oval frame and six candelabra light bases.
Figure 2: Dimensional drawing of the Fontayne Six-Light Chandelier. This diagram illustrates the fixture's height (15-3/4 inches), width (36 inches), and overall hanging length (22 inches from ceiling to top of fixture).
Step 3: Wire the Fixture
- Connect the bare copper ground wire from the fixture to the ground wire from the outlet box (usually green or bare copper) using a wire nut.
- Connect the white wire from the fixture to the white (neutral) wire from the outlet box using a wire nut.
- Connect the black wire from the fixture to the black (hot) wire from the outlet box using a wire nut.
- Ensure all wire connections are secure and tuck them carefully into the outlet box.
- Slide the canopy up against the ceiling and secure it with the provided screws or decorative nuts.
Step 4: Install Light Bulbs
- Insert six (6) candelabra base bulbs (B10 type, 60 watts maximum each) into the sockets. Do not exceed the maximum wattage.
Figure 3: Close-up view of a candelabra light socket. This image highlights the base where the B10 type bulb is inserted.
- Restore power at the main fuse box or circuit breaker.
- Test the fixture to ensure proper operation.
Operating Instructions
Once installed, the Fontayne Six-Light Chandelier operates like any standard light fixture. Control the light using the wall switch connected to the fixture's circuit. This fixture is designed for on/off functionality and does not include integrated dimming capabilities unless connected to a compatible dimmer switch (sold separately).
Maintenance
Cleaning
- Always disconnect power before cleaning.
- To clean the fixture, wipe it with a soft, dry cloth.
- Do not use abrasive cleaners, polishes, or solvents as they may damage the finish.
Bulb Replacement
- Ensure power is disconnected at the circuit breaker before replacing bulbs.
- Allow bulbs to cool completely before touching them.
- Unscrew the old bulb and replace it with a new B10 candelabra base bulb, not exceeding 60 watts.
Troubleshooting
If you experience issues with your chandelier, refer to the table below for common problems and solutions.
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on. | 1. Power is off. 2. Faulty bulb. 3. Incorrect wiring. | 1. Check circuit breaker/fuse. 2. Replace bulb. 3. Verify wiring connections (consult electrician if unsure). |
| Light flickers. | 1. Loose bulb. 2. Loose wiring connection. 3. Incompatible dimmer switch. | 1. Tighten bulb. 2. Check wiring connections. 3. Ensure dimmer is compatible with LED/incandescent bulbs. |
| Fixture hums. | 1. Loose wiring. 2. Incompatible dimmer. | 1. Check wiring connections. 2. Replace dimmer with a compatible one. |
Product Specifications
| Specification | Detail |
|---|---|
| Model Number | P400082-009 |
| Brand | Progress Lighting |
| Fixture Type | Chandelier |
| Number of Lights | 6 |
| Light Source | B10 Candelabra Base |
| Max Wattage per Bulb | 60 watts |
| Voltage | 120 volts |
| Material | Alloy Steel, Glass |
| Finish | Brushed Nickel with weathered gray accents |
| Indoor/Outdoor Usage | Indoor |
| Item Weight | 11.7 pounds |
| Certification | ETL Listed |
Warranty and Customer Support
This Progress Lighting product is covered by a 1-year Limited Warranty from the date of purchase. This warranty guarantees your complete satisfaction with your purchase and includes professional after-sales customer service support. The warranty covers defects in materials and workmanship under normal use.
For warranty claims, technical assistance, or missing parts, please contact Progress Lighting customer service. Keep your proof of purchase for warranty validation.
For more information, visit the official Progress Lighting Store.