1. Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your Cooper Lighting All Pro MS34W Motion Detector Floodlight. Please read this manual thoroughly before installation and use to ensure proper function and safety.
The All Pro MS34W is a white incandescent outdoor spotlight equipped with a 110-degree motion sensor, designed to provide security lighting by activating upon detecting movement.
2. Safety Information
WARNING: Risk of electric shock. Disconnect power at the fuse or circuit breaker before installation or servicing. All wiring connections must be made by a qualified electrician in accordance with local electrical codes.
- Ensure the power supply is turned off before handling the floodlight.
- Do not install near combustible materials or in areas with explosive atmospheres.
- This product is designed for outdoor use. Ensure all connections are weatherproof.
- Do not exceed the maximum wattage rating for bulbs.
- Wear appropriate safety gear, including gloves and eye protection, during installation.
3. Package Contents
Verify that all components are present before beginning installation:
- All Pro MS34W Motion Detector Floodlight (1 unit)
- Mounting Hardware (screws, wire nuts, gasket)
Image 1: Cooper Lighting All Pro MS34W Motion Detector Floodlight. This image shows the white floodlight fixture with two adjustable lamp heads and a central motion sensor unit.
4. Setup
4.1 Mounting
- Select Location: Choose a suitable outdoor location, such as a wall or eave, ensuring the motion sensor has an unobstructed view of the desired detection area. Avoid aiming the sensor at reflective surfaces or heat sources that could cause false triggers.
- Prepare Mounting Surface: Ensure the mounting surface is stable and can support the weight of the fixture.
- Install Mounting Hardware: Secure the mounting plate (if applicable) to the junction box using the provided screws. Ensure the gasket is properly seated to prevent water intrusion.
4.2 Wiring
IMPORTANT: Ensure power is OFF at the circuit breaker before proceeding with wiring.
- Connect Ground Wire: Connect the bare copper or green ground wire from the fixture to the ground wire from the junction box using a wire nut.
- Connect Neutral Wire: Connect the white neutral wire from the fixture to the white neutral wire from the junction box using a wire nut.
- Connect Live Wire: Connect the black live wire from the fixture to the black live wire from the junction box using a wire nut.
- Secure Fixture: Carefully tuck all wires into the junction box and secure the floodlight fixture to the mounting plate.
4.3 Initial Power-Up and Testing
- Restore Power: Turn the power back ON at the circuit breaker.
- Test Mode: The floodlight may enter a test mode, staying on for a short period or cycling. Follow specific instructions on the fixture itself or in supplementary documentation for adjusting sensor settings.
- Adjust Lamp Heads: Aim the two floodlight lamp heads to cover the desired illumination area.
5. Operating Instructions
5.1 Motion Sensor Adjustment
The motion sensor typically features adjustable controls for sensitivity and time duration. These controls are usually located on the underside or side of the sensor unit.
- Sensitivity (SENS): Adjusts how far the sensor can detect motion. A higher setting increases the detection range.
- Time (TIME): Sets how long the light remains on after motion is detected and stops. Common settings range from a few seconds to several minutes.
- Dusk-to-Dawn (LUX/DAYLIGHT): This control determines the ambient light level at which the sensor becomes active. Set to a lower LUX for activation only in darker conditions, or higher for activation in brighter conditions.
5.2 Light Operation Modes
The floodlight operates primarily in motion-activated mode. Depending on the LUX setting, it will only activate when motion is detected during low light conditions. Some models may offer a manual override to keep the lights on continuously; refer to the specific controls on your unit for this feature.
6. Maintenance
6.1 Cleaning
To maintain optimal performance and appearance, clean the floodlight periodically. Ensure power is disconnected before cleaning.
- Wipe the fixture with a soft, damp cloth.
- Do not use abrasive cleaners, solvents, or cleaners containing alcohol, as these can damage the finish or sensor lens.
- Gently clean the motion sensor lens to ensure clear detection.
6.2 Bulb Replacement
WARNING: Disconnect power before replacing bulbs. Allow bulbs to cool completely before touching.
- Ensure power to the fixture is turned off at the circuit breaker.
- Allow the existing bulb(s) to cool down if they have been recently in use.
- Carefully unscrew the old incandescent bulb(s) from the lamp holder.
- Screw in new incandescent bulb(s) of the correct type and wattage (up to 300 watts total for the fixture). Do not overtighten.
- Restore power and test the floodlight.
7. Troubleshooting
If your floodlight is not operating correctly, refer to the following table for common issues and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on. | No power; faulty bulb; sensor setting too low (LUX); wiring issue. | Check circuit breaker; replace bulb; adjust LUX setting; verify wiring connections. |
| Light stays on continuously. | Sensor in test mode; continuous motion detected; wiring error; faulty sensor. | Allow test mode to expire; check for constant motion in detection zone; verify wiring; contact support if sensor is faulty. |
| Light turns on for no apparent reason. | Sensor too sensitive; heat sources or reflective objects in detection zone; small animals. | Reduce sensitivity (SENS); reposition sensor to avoid false triggers; clear detection zone. |
| Detection range is too short or too long. | Incorrect sensitivity setting; obstruction. | Adjust sensitivity (SENS) control; ensure clear line of sight for the sensor. |
If troubleshooting steps do not resolve the issue, contact Cooper Lighting customer support or a qualified electrician.
8. Specifications
| Feature | Specification |
|---|---|
| Brand | Cooper Lighting |
| Model Number | MS34W |
| Material | Plastic |
| Light Fixture Form | Floodlight |
| Specific Uses | Outdoor |
| Power Source | Corded Electric |
| Special Feature | Motion Sensor |
| Wattage | Up to 300 watts (total) |
| Item Weight | 5.7 Pounds |
| Product Dimensions | 15.38 x 10.25 x 6.25 inches |
| Mounting Type | Wall Mount |
| UPC | 044427351284 |
9. Warranty and Support
For warranty information, please refer to the documentation included with your purchase or visit the official Cooper Lighting website. Warranty terms typically cover defects in materials and workmanship for a specified period from the date of purchase.
If you require technical assistance or have questions not covered in this manual, please contact Cooper Lighting customer support through their official channels. Keep your purchase receipt and model number (MS34W) available when contacting support.