Hydro Guard Dechlorinating Shower Filter with Shower Head (Chrome) Instruction Manual

1. Product Overview

The Hydro Guard Dechlorinating Shower Filter with Shower Head is designed to provide a healthier and more enjoyable showering experience by filtering out harmful chemicals from your tap water. This system easily attaches to your existing shower line without the need for special tools.

Its unique two-stage up-flow filter design incorporates coconut shell carbon and a KDF copper/zinc oxidation process. This combination effectively removes harsh chemicals such as chlorine, lead, pesticides, hydrogen sulfides, and other volatile organic compounds. The coconut shell carbon also works to improve the taste and smell of your water.

Benefits include softer, more moisturized skin, and shinier, healthier hair. It also helps reduce itchy skin or scalp, extends hair color, and reduces frizz and comb-ability. The filter adjusts the pH of the water and minimizes chlorine absorption through the skin and inhalation.

Figure 1: Hydro Guard Dechlorinating Shower Filter with Shower Head (Chrome) - This image displays the complete shower filter unit, including the main filter housing and the attached shower head, in a chrome finish.

2. Safety Information

• Ensure all connections are tight to prevent leaks. Do not overtighten.
• Use only with cold or warm water. Do not use with hot water exceeding recommended temperatures (typically 100-110°F or 38-43°C).
• Do not use the filter with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.
• Keep out of reach of children.
• Inspect the unit periodically for any signs of damage or wear. Replace if necessary.

3. Package Contents

Please verify that all components are present before beginning installation:

• Hydro Guard Dechlorinating Shower Filter Unit (Chrome)
• Shower Head (Chrome)
• Instruction Manual

4. Setup and Installation

Installation of the Hydro Guard shower filter is designed to be simple and requires no special tools. Follow these steps for a quick setup:

1. Prepare the Shower Area: Turn off the water supply to your shower. If you have an existing shower head, unscrew it from the shower arm by turning it counter-clockwise. Clean any residue or old Teflon tape from the threads of the shower arm.
2. Install the Filter Unit: Take the Hydro Guard shower filter unit. Ensure the rubber washer is properly seated inside the filter's inlet (the end that connects to the shower arm). Screw the filter unit onto the shower arm by turning it clockwise until it is hand-tight. Do not overtighten.
3. Attach the Shower Head: Ensure the rubber washer is properly seated inside the shower head's inlet. Screw the provided shower head onto the outlet of the filter unit by turning it clockwise until it is hand-tight. Do not overtighten.
4. Check for Leaks: Turn on the water supply slowly and check for any leaks at the connections. If leaks occur, tighten slightly until they stop. If leaks persist, ensure washers are correctly seated and connections are aligned.
5. Flush the Filter: Before first use, allow water to run through the shower head for 5-10 minutes to flush out any carbon fines or air from the filter. The water may appear cloudy initially; this is normal and will clear up.

Figure 2: Internal Structure of the Shower Filter - This diagram illustrates the four stages of filtration: Bioceramic pH Balancing Media, 25 Micron Sediment Filtration, Coconut Shell Carbon, and KDF Chlorine Scavenging Media.

5. Operating Instructions

Once installed and flushed, the Hydro Guard shower filter operates automatically. Simply turn on your shower as you normally would. The filter will continuously process the water as it passes through, providing you with filtered water for your shower.

• Ensure the water temperature is within the recommended range for shower use.
• No special settings or adjustments are required for daily operation.

6. Maintenance

Regular maintenance ensures optimal performance and longevity of your Hydro Guard shower filter.

Filter Replacement

The filter cartridge should be replaced every 10,000 gallons or every 6 months, whichever comes first. This ensures continued effectiveness in removing contaminants.

1. Turn off the water supply to your shower.
2. Unscrew the shower head from the filter unit.
3. Unscrew the filter unit from the shower arm.
4. Carefully separate the two halves of the filter housing to access the old filter cartridge.
5. Remove the old cartridge and dispose of it properly.
6. Insert a new Hydro Guard replacement filter cartridge, ensuring it is seated correctly.
7. Reassemble the filter housing, screw it back onto the shower arm, and reattach the shower head.
8. Turn on the water supply and flush the new filter for 5-10 minutes as described in the installation section.

Cleaning the Shower Head

Periodically clean the nozzles of the shower head to prevent mineral buildup and maintain spray performance. You can gently rub the rubber nozzles or use a soft brush with a mild descaling solution if necessary.

7. Troubleshooting

8. Specifications

9. Warranty and Support

Specific warranty details for the Hydro Guard Dechlorinating Shower Filter are not provided in this manual. For warranty information, technical support, or to purchase replacement filters, please contact the manufacturer, Hydro Guard, directly or visit their official website.

Please retain your proof of purchase for any warranty claims.