8Bitdo Wireless USB Adapter 1 Instruction Manual

1. Introduction and Overview

The 8Bitdo Wireless USB Adapter 1 allows you to connect a wide range of wireless controllers to various platforms, including Nintendo Switch, Windows PCs, macOS, and Raspberry Pi. This adapter enhances your gaming experience by enabling the use of your preferred controllers across different systems.

Figure 1: The 8Bitdo Wireless USB Adapter 1, a compact, brick-shaped USB dongle.

2. Product Features

• System Compatibility: Nintendo Switch, Switch OLED, Windows PC, macOS, and Raspberry Pi.
• Controller Compatibility: All 8BitDo Bluetooth Controllers and Arcade Sticks, PS5, PS4, PS3 Controllers, Switch Pro, Switch Joy-con, Wii Mote, Wii U Pro, and more.
• Ultimate Software Support: Customize button mapping, adjust stick and trigger sensitivity, control vibration, and create macros with any button combination.
• Motion and Vibration: Supports 6-axis motion on Switch and vibration in X-input mode.
• Important Note: Xbox Bluetooth controllers on the latest firmware released in September 2021 are NOT supported due to changes in their Bluetooth protocol from Classic to BLE.

3. Setup Guide

3.1. General Setup

1. Plug the 8Bitdo Wireless USB Adapter 1 into an available USB port on your desired system (Nintendo Switch dock, PC, Mac, Raspberry Pi).
2. The adapter's LED will begin to blink, indicating it is in pairing mode.
3. Activate pairing mode on your controller (refer to your controller's manual for specific instructions).
4. Once paired, the adapter's LED will become solid, and your controller will be ready for use.

Figure 2: The 8Bitdo Wireless USB Adapter 1, ready to be plugged into a USB port.

3.2. Nintendo Switch Setup

1. Ensure your Nintendo Switch is updated to the latest firmware.
2. Go to System Settings > Controllers and Sensors.
3. Enable "Pro Controller Wired Communication" by setting it to "On". This is crucial for the adapter to function correctly.
4. Plug the 8Bitdo Wireless USB Adapter 1 into an available USB port on the Nintendo Switch dock.
5. Follow the general pairing instructions (Section 3.1) to connect your controller.

Figure 3: The adapter enables compatibility with a wide range of controllers on the Nintendo Switch.

3.3. Windows PC Setup

1. Plug the 8Bitdo Wireless USB Adapter 1 into an available USB port on your Windows PC.
2. The adapter will typically be recognized as an X-input device, providing broad compatibility with PC games.
3. Follow the general pairing instructions (Section 3.1) to connect your controller.

3.4. macOS & Raspberry Pi Setup

1. Plug the 8Bitdo Wireless USB Adapter 1 into an available USB port on your macOS device or Raspberry Pi.
2. The adapter will function as a standard Bluetooth game controller.
3. Follow the general pairing instructions (Section 3.1) to connect your controller.

3.5. PS3 Controller Specific Pairing

To pair a PS3 controller, a computer is required for the initial setup:

1. Download the 8Bitdo Retro Receiver Tools from the official 8Bitdo support website.
2. Connect your PS3 controller to your computer via a USB cable.
3. Hold down the pair button on the 8Bitdo Wireless USB Adapter 1 and connect it to your computer via a USB cable.
4. Open the 8Bitdo Retro Receiver Tools software and click the "Pair" button. This will link the PS3 controller to the adapter.
5. Once paired, you can disconnect both the controller and adapter from the computer and use the adapter with your PS3 controller on other compatible systems.

4. Operating Instructions

Once your controller is successfully paired with the 8Bitdo Wireless USB Adapter 1, it will function as a native controller for the connected system. Button mappings will generally correspond to the system's standard layout. For advanced customization, refer to the Ultimate Software section.

To re-connect a previously paired controller, simply turn on the controller and ensure the adapter is plugged into the system. The connection should be established automatically.

5. Advanced Features: Ultimate Software

The 8Bitdo Ultimate Software allows for extensive customization of your compatible controllers when used with the Wireless USB Adapter 1. This software is compatible with PS5, PS4, Xbox One S/X Bluetooth Controllers, and Switch Pro controllers only.

With the Ultimate Software, you can:

• Remap buttons to your preferred layout.
• Adjust the sensitivity of analog sticks and triggers.
• Control vibration intensity.
• Create and assign macros for complex button combinations.

Visit the official 8Bitdo website for more information and to download the Ultimate Software.

6. Troubleshooting

• Controller Not Connecting: Ensure the adapter is in pairing mode (blinking LED) and your controller is also in its respective pairing mode. Try restarting both the adapter (by unplugging and re-plugging) and the controller.
• Nintendo Switch Issues: Verify that "Pro Controller Wired Communication" is enabled in the Switch System Settings.
• Xbox Controller Compatibility: Xbox Bluetooth controllers with firmware released after September 2021 are NOT supported. Ensure your Xbox controller is an older model or has compatible firmware.
• PS3 Controller Pairing: Remember that PS3 controllers require an initial wired pairing process with a computer using the 8Bitdo Retro Receiver Tools.
• Firmware Updates: Regularly check the official 8Bitdo website for firmware updates for your adapter. Updates can improve compatibility and add new features.

7. Specifications

• Model Number: 6922621500285
• Product Dimensions: 5.12 x 9.84 x 6.3 inches
• Item Weight: 0.8 ounces
• Connectivity: Bluetooth
• Manufacturer: 8Bitdo

8. Warranty and Support

For warranty information, technical support, and the latest firmware updates, please visit the official 8Bitdo support website. You can find detailed FAQs and contact information for customer service there.

Official 8Bitdo Website: www.8bitdo.com/support/