Zooz Momentary Push-Button in-Wall Switch ZAC99 Instruction Manual

Product Overview

The Zooz ZAC99 is a momentary push-button in-wall switch designed for various applications requiring temporary contact closure. It is suitable for controlling devices such as garbage disposals or as an accessory switch for Z-Wave dimmer modules to enable local dimming control. This device is not a Z-Wave switch itself but functions as a momentary contact switch.

Key Features:

• Versatile Application: Can be used for garbage disposals or as a local control for Z-Wave dimmer modules.
• Momentary Control: Activates a connected device only while the button is pressed.
• Flexible Installation: Compatible with 14 AWG and 12 AWG wires, supporting loads up to 15 A.
• Compact Design: Slim profile allows for easier installation in standard switch boxes.

Image: Front view of the Zooz ZAC99 Momentary Push-Button in-Wall Switch. This image shows the white paddle-style button and the mounting frame.

Safety Information

• WARNING: Risk of Electric Shock. All service should be performed by qualified personnel only.
• Disconnect power at the circuit breaker or fuse box before installation.
• Ensure all wiring connections are secure and comply with local electrical codes.
• This device is intended for indoor use only.
• Do not exceed the maximum load rating of 15 Amps.

Installation (Setup)

Follow these steps for safe and proper installation of your Zooz ZAC99 Momentary Push-Button in-Wall Switch.

1. Turn Off Power: Locate the circuit breaker controlling the switch location and turn off the power. Verify power is off using a voltage tester.
2. Remove Existing Switch: Carefully remove the wall plate and unscrew the existing switch from the electrical box. Disconnect the wires from the old switch.
3. Identify Wires:
   • Line (Hot) Wire: Typically black, brings power from the circuit breaker.
   • Load Wire: Typically black, connects to the light fixture or appliance.
   • Ground Wire: Bare copper or green, connects to the electrical box or ground screw.
4. Wire the ZAC99 Switch:
   

   Image: Back view of the Zooz ZAC99 switch, illustrating the screw terminals for wiring connections.

   • Connect the Line (Hot) wire to one of the screw terminals on the ZAC99 switch.
   • Connect the Load wire to the other screw terminal on the ZAC99 switch.
   • Connect the Ground wire to the green ground screw on the switch or the electrical box.
   • Ensure all connections are tight and secure. The switch accepts 14 AWG and 12 AWG wires.
5. Mount the Switch: Carefully push the wired switch into the electrical box. Secure it with the provided screws.
6. Install Wall Plate: Attach the wall plate over the switch.
7. Restore Power: Turn the power back on at the circuit breaker.

Note: This switch is a momentary contact switch. It does not have a neutral wire connection and is designed for simple on/off momentary control. For advanced functionality with Z-Wave dimmer modules, refer to the specific instructions for your Z-Wave device regarding momentary switch configuration.

Operating Instructions

The Zooz ZAC99 switch provides momentary control based on its application.

For Garbage Disposals or Similar Devices:

• To Activate: Press and hold the upper part of the paddle switch. The connected device (e.g., garbage disposal) will remain active as long as the button is held.
• To Deactivate: Release the button. The device will turn off.

When Used with a Z-Wave Dimmer Module (Accessory Control):

When configured with a compatible Z-Wave dimmer module (e.g., Aeotec ZW111, Fibaro FGD-212, Qubino ZMNHDD3, ZMNHWD3), the ZAC99 can provide local control for lighting.

• Turn On/Off: Tap the upper part of the paddle switch once to toggle the light on or off.
• Adjust Brightness: Press and hold the upper part of the paddle switch to adjust the brightness. Release when the desired brightness level is reached.

Important: The Z-Wave dimmer module must be configured to recognize a momentary switch for this functionality. Refer to your Z-Wave dimmer module's instruction manual for specific configuration settings (e.g., parameter settings for momentary switch type).

Maintenance

The Zooz ZAC99 switch requires minimal maintenance.

• Cleaning: To clean the switch, wipe it with a soft, damp cloth. Do not use abrasive cleaners or solvents. Ensure power is off before cleaning.
• Periodic Checks: Periodically check the wall plate and switch for any signs of damage or loose connections. If any issues are observed, turn off power and consult a qualified electrician.

Troubleshooting

If you experience issues with your ZAC99 switch, refer to the following common solutions:

• Device Not Responding:
  • Ensure power is supplied to the switch at the circuit breaker.
  • Verify all wiring connections are secure and correct.
  • Check the connected load (e.g., garbage disposal) to ensure it is functioning correctly.
• Not Controlling Z-Wave Dimmer Module:
  • Confirm that the Z-Wave dimmer module is properly installed and powered.
  • Ensure the Z-Wave dimmer module is configured to operate with a momentary switch. This usually involves adjusting a parameter in your Z-Wave hub or controller settings. Refer to the dimmer module's manual for specific instructions (e.g., Zooz Zen72, Option 19, set to Momentary switch).
  • Verify the wiring between the ZAC99 and the Z-Wave dimmer module is correct according to the dimmer module's accessory switch wiring diagram.
• Switch Feels Stiff or Hard to Press:
  • The switch is designed for a tactile click. If it feels unusually stiff or unresponsive, ensure it is properly seated in the electrical box and not obstructed by the wall plate.

Specifications

Warranty and Support

For warranty information or technical support, please contact Zooz directly. Refer to the official Zooz website or your purchase documentation for the most current support contact details and warranty terms.

Brand: ZOOZ

Manufacturer: ZOOZ

Website: Visit the ZOOZ Store on Amazon