Introduction
The Revell Control GO! Stunt Quadrocopter is a 31 cm remote-controlled quadrocopter designed for both indoor and outdoor use. It features a 6-axis gyroscope for enhanced stability, making it suitable for beginners. Key functions include Headless Mode for simplified control, a looping function, and adjustable responsiveness. The drone is equipped with protective motor and propeller guards, and LED position lights to distinguish the front from the rear during flight.
Safety Information
Warning: Not suitable for children under 3 years of age due to small parts. Recommended for ages 12 and up.
- Always operate the quadrocopter in open areas, away from people, animals, and obstacles.
- Do not fly near high-voltage lines, trees, or water.
- Ensure the battery is fully charged before each flight.
- Never leave charging batteries unattended.
- Keep fingers and hair away from rotating propellers.
- Do not modify the quadrocopter or its components.
Package Contents
Verify that all items are present in the package:
- Revell Control GO! Stunt Quadrocopter
- Remote Control (2.4 GHz)
- 3.7V 380 mAh LiPo Battery
- USB Charger
- Spare Propeller Set
Image: All components included in the Revell Control GO! Stunt Quadrocopter package.
Setup
1. Battery Charging
- Connect the LiPo battery to the provided USB charger.
- Plug the USB charger into a compatible USB power source (e.g., computer USB port, USB wall adapter).
- The charging indicator light on the USB charger will illuminate during charging and turn off when the battery is fully charged.
- Charging typically takes 50 to 60 minutes for approximately 7 minutes of flight time.
2. Remote Control Preparation
- Install 4x AA batteries (not included) into the remote control, observing correct polarity.
- Ensure the remote control is switched off before proceeding.
3. Drone Preparation
- Carefully insert the fully charged LiPo battery into the battery compartment of the quadrocopter.
- Connect the battery cable to the drone's power port.
- Place the quadrocopter on a flat, level surface.
Operating Instructions
1. Pairing the Quadrocopter and Remote Control
- Turn on the quadrocopter. The LED lights will flash.
- Turn on the remote control.
- Move the left joystick (throttle) all the way up, then all the way down. The drone's LED lights will stop flashing and remain solid, indicating successful pairing.
2. Take-off and Basic Flight
- Take-off: Gently push the left joystick (throttle) upwards to increase propeller speed and lift off.
- Ascend/Descend: Use the left joystick (throttle) to control altitude.
- Forward/Backward: Push the right joystick forward or backward.
- Left/Right: Push the right joystick left or right to move sideways.
- Rotation: Push the left joystick left or right to rotate the quadrocopter.
3. Special Functions
- Headless Mode: Press the Headless Mode button. In this mode, the drone's orientation relative to the pilot is fixed, regardless of which way the drone is facing. This simplifies control for beginners.
- Looping Function: Press the Looping button, then quickly move the right joystick in the desired direction (forward, backward, left, or right) to perform a 360-degree flip.
- Adjustable Responsiveness: The remote control allows for adjusting the drone's responsiveness (speed/sensitivity) to suit different skill levels. Refer to the remote control diagram for specific buttons.
Image: The quadrocopter being held, illustrating its size and handling.
Maintenance
1. Propeller Replacement
- If a propeller is damaged, carefully remove it.
- Replace with a new propeller from the spare set, ensuring it is installed on the correct motor (propellers are typically marked A or B).
2. Cleaning
- Use a soft, dry cloth to clean the quadrocopter and remote control.
- Do not use water or chemical cleaners, as this can damage electronic components.
3. Storage
- Store the quadrocopter and remote control in a cool, dry place when not in use.
- Remove batteries from the remote control if storing for extended periods.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Quadrocopter does not respond to remote control. | Not paired; low battery in drone or remote. | Ensure proper pairing sequence. Charge drone battery. Replace remote control batteries. |
| Drone flies erratically or drifts. | Uncalibrated gyroscope; damaged propeller. | Place drone on a flat surface and re-calibrate (refer to remote control instructions for calibration steps). Check and replace damaged propellers. |
| One propeller spins independently or drone shuts off mid-flight. | Motor malfunction; battery issue. | Disconnect and reconnect the battery. If the problem persists, contact customer support. |
| Short flight time. | Battery not fully charged; aging battery. | Ensure battery is fully charged. Consider replacing the battery if it's old. |
Specifications
- Brand: Revell Control
- Model: GO! Stunt
- Model Number: Revell_23842
- Item Weight: 100 grams
- Product Dimensions (L x W x H): 51 x 9 x 34 cm
- Battery: 1 Lithium metal battery (included), 3.7V 380 mAh LiPo
- Charging Time: 50-60 minutes
- Flight Time: Approximately 7 minutes
- Connectivity Technology: USB (for charging)
- Special Features: Flashing lights, lightweight design, 6-axis gyroscope, Headless Mode, Looping function
- Recommended Age: 12 to 99 years
- Country of Origin: China
Warranty and Support
For warranty information or technical support, please refer to the documentation included with your purchase or contact Revell Control customer service directly. Contact details can typically be found on the product packaging or the official Revell Control website.