1. Introduction
The Panduit LWC100-A-L Latching Wire Clip is designed for efficient and secure management of electrical cables and wires. This clip features a durable nylon 6.6 construction and an adhesive-backed mounting base, allowing for flexible installation on various surfaces. Its unique latching mechanism enables easy attachment and detachment of cables without disturbing the mounted clip.
Key features include:
- Route and secure cords and cables effectively.
- Convenient releasable latch for easy cable access.
- Available in multiple sizes to accommodate various bundle diameters.
- Rubber-based adhesive provides a strong and reliable bond.
- UL Recognized for quality assurance, ensuring product reliability.
2. Setup and Installation
Proper installation ensures optimal performance and longevity of the wire clip. Follow these steps for secure mounting:
- Surface Preparation: Ensure the mounting surface is clean, dry, and free of dust, grease, or any contaminants. For best adhesion, clean the surface with an appropriate cleaner and allow it to dry completely.
- Peel Adhesive Backing: Carefully peel off the protective liner from the rubber adhesive foam tape on the back of the wire clip. Avoid touching the adhesive surface to maintain its bonding strength.
- Positioning: Place the wire clip firmly onto the desired surface. Apply even pressure across the entire adhesive base for at least 30 seconds to ensure a strong bond. The rubber adhesive foam tape is designed for conformable contact with uneven surfaces.
- Curing Time: Allow the adhesive to cure for a recommended period (typically 24 hours) before applying significant load or routing cables, to achieve maximum bond strength.
3. Operating Instructions
The latching wire clip provides a simple and effective way to manage cables. Follow these instructions for use:
- Opening the Latch: To insert or remove cables, gently press the top part of the latching mechanism. This will release the latch, allowing the clip to open.
- Inserting Cables: Place the cables or wires into the open clip. Ensure the bundle diameter does not exceed the clip's maximum capacity (1.00-inch for this model) to prevent damage or improper closure.
- Closing the Latch: Once cables are positioned, press the latch firmly until it clicks into place, securing the cables within the clip.
- Releasing Cables: To remove or adjust cables, simply press the latch again to open the clip. This allows for easy modification of cable routing without needing to remove the entire clip from its mounted surface.
4. Maintenance
The Panduit LWC100-A-L Latching Wire Clip requires minimal maintenance. To ensure its continued performance and appearance:
- Cleaning: If necessary, gently wipe the clip with a soft, damp cloth to remove dust or light grime. Avoid using harsh chemicals or abrasive cleaners, as these may damage the nylon material or the adhesive.
- Inspection: Periodically inspect the clip and its adhesive bond to ensure it remains securely attached to the surface and the latching mechanism operates smoothly.
5. Troubleshooting
This section addresses common issues you might encounter with the Panduit LWC100-A-L Latching Wire Clip.
| Problem | Possible Cause | Solution |
|---|---|---|
| Clip does not adhere properly to surface. | Surface was not clean or dry; insufficient pressure applied during installation; adhesive not fully cured. | Ensure surface is thoroughly cleaned and dry before application. Apply firm, even pressure for at least 30 seconds. Allow 24 hours for adhesive to cure before loading. If necessary, replace the clip. |
| Latching mechanism is stiff or does not close. | Excessive cable bundle size; debris in the latch mechanism. | Ensure cable bundle diameter does not exceed 1.00 inch. Check for and remove any debris obstructing the latch. |
| Cables fall out of the clip. | Latching mechanism not fully closed; bundle too small for secure fit; clip damaged. | Ensure the latch clicks securely into place. Verify the cable bundle size is appropriate for the clip. If the clip is damaged, replace it. |
6. Specifications
| Attribute | Detail |
|---|---|
| Model Number | LWC100-A-L |
| Material | Nylon 6.6 |
| Mounting Type | Adhesive Backed (Rubber Adhesive Foam Tape) |
| Maximum Bundle Diameter | 1.00-Inch |
| Color | Natural |
| Package Quantity | 50-Pack |
| Compliance | UL Recognized, RoHS Compliant |
| Package Dimensions | 12.5 x 11.4 x 3.1 inches |
| Item Weight | 1.45 Pounds |
7. Warranty Information
Panduit products are manufactured to high-quality standards. Specific warranty terms and conditions for the LWC100-A-L Latching Wire Clip are typically provided by the manufacturer at the time of purchase or can be found on the official Panduit website. Please refer to the documentation included with your purchase or visit the Panduit website for detailed warranty information.
8. Support
For technical assistance, product inquiries, or further support regarding your Panduit LWC100-A-L Latching Wire Clip, please contact Panduit customer service or visit their official website. You can find more information and contact details by visiting the Panduit Store on Amazon or their corporate website.
