Introduction
This manual provides detailed instructions for the Invicta Bolt Quartz Chronograph Watch, Model 25519. Please read this manual thoroughly to understand the functions and proper care of your timepiece.
Key Features:
- 52mm stainless steel case with a two-tone finish.
- Green dial with chronograph subdials.
- Flame Fusion crystal for enhanced durability.
- Water resistant up to 100 meters (330 feet).
- Quartz movement with chronograph functions: 60-second, 60-minute, and 24-hour subdials.
- Luminous accents for visibility in low light.
Setup Instructions
Setting the Time:
- Pull the crown out to position 2 (the outermost position).
- Turn the crown clockwise or counter-clockwise to set the hour and minute hands to the desired time.
- Push the crown back into position 0 (normal operating position).
Setting the Date (if applicable):
- Pull the crown out to position 1 (the middle position).
- Turn the crown clockwise or counter-clockwise to set the date. Avoid setting the date between 9 PM and 3 AM, as this may damage the movement.
- Push the crown back into position 0.
Initial Chronograph Reset:
If the chronograph hands are not aligned to the 12 o'clock position, they may need to be reset.
- Pull the crown out to position 2.
- Press button A (top pusher) to advance the 60-second chronograph hand.
- Press button B (bottom pusher) to advance the 60-minute chronograph hand.
- Once all chronograph hands are aligned to 12 o'clock, push the crown back into position 0.
Image: Front view of the Invicta Bolt Chronograph Watch, highlighting the crown and chronograph pushers (A and B) on the side of the case.
Operating Instructions
Using the Chronograph:
The chronograph function allows for precise timing of events.
- Start: Press button A (top pusher) to start the chronograph. The 60-second hand will begin to move.
- Stop: Press button A again to stop the chronograph. The elapsed time will be indicated by the 60-second, 60-minute, and 24-hour subdials.
- Reset: After stopping the chronograph, press button B (bottom pusher) to reset all chronograph hands to their 12 o'clock positions.
- Split Time (if applicable): Some chronographs allow for split-time measurement. Consult the specific movement manual if this feature is desired.
Maintenance and Care
Water Resistance:
This watch is water resistant up to 100 meters (330 feet). This rating makes it suitable for showering, swimming, and snorkeling. However, it is not suitable for diving. Ensure the crown is fully pushed in before any contact with water. Do not operate the crown or pushers while the watch is wet or submerged.
Cleaning:
To maintain the appearance of your watch, clean the case and bracelet regularly with a soft, damp cloth. For stainless steel bracelets, a mild soap solution can be used, followed by thorough rinsing and drying. Avoid harsh chemicals or abrasive materials.
Battery Replacement:
The watch is powered by a quartz movement requiring a product-specific battery. When the battery is depleted, the watch hands may stop or the second hand may jump in multi-second intervals (End-of-Life indicator). Battery replacement should be performed by a qualified watch technician to ensure proper sealing and water resistance.
Crystal Care:
The watch features a Flame Fusion crystal, known for its scratch resistance. While durable, avoid direct impact or abrasive contact to prevent damage.
Image: Rear view of the Invicta Bolt Chronograph Watch, displaying engravings for "100M Water Resistant" and "Flame-Fusion Crystal", along with the model number 25519.
Troubleshooting
- Watch Not Running: Check if the crown is fully pushed in. If the watch still does not run, the battery may need replacement.
- Chronograph Hands Not Resetting to Zero: Perform the "Initial Chronograph Reset" procedure described in the Setup section.
- Date Not Changing: Ensure the time is set correctly, passing midnight. If the date is stuck, try manually advancing it using the crown in position 1. Avoid setting the date during the forbidden hours (9 PM - 3 AM).
- Water Inside Watch: If moisture or condensation appears inside the watch, immediately take it to a qualified service center. This indicates a breach in water resistance.
Specifications
| Feature | Detail |
|---|---|
| Model Number | 25519 |
| Case Material | Stainless Steel |
| Case Diameter | 52 mm |
| Case Thickness | 18.5 mm |
| Band Material | Stainless Steel |
| Band Width | 26 mm |
| Band Length | 185 mm |
| Crystal Type | Flame Fusion |
| Movement Type | Quartz |
| Display Type | Analog |
| Water Resistance Depth | 100 Meters (330 Feet) |
| Additional Features | Chronograph, Dual-Time-Display, Luminous |
| Clasp Type | Fold-over-clasp-with-safety |
| Item Weight | 250 Grams |
Warranty Information
Invicta offers a limited warranty for its timepieces. This watch is covered by a 2-year international warranty from the date of purchase, covering manufacturing defects. Please retain your proof of purchase for warranty claims.
Extended protection plans may also be available for purchase:
- 2-Year Protection Plan: One-time payment of $15.99
- 3-Year Protection Plan: One-time payment of $21.99
For detailed terms and conditions of the warranty and protection plans, please refer to the official Invicta warranty documentation included with your watch or visit the Invicta website.
Image: A graphic indicating "2 Year International Warranty" for Invicta products.
Customer Support
For further assistance, service, or inquiries regarding your Invicta Bolt Quartz Chronograph Watch Model 25519, please contact Invicta customer service or visit the official Invicta website.
You can also find more information and products at the Invicta Store on Amazon.
Image: The Invicta watch packaging box, which typically contains the watch, manual, and warranty information.
