Introduction
This manual provides instructions for the setup, operation, and maintenance of your Anderic OEM Xfinity/Comcast Digital Transport Adapter (DTA) Remote Control. This remote is designed to control your Xfinity/Comcast DTA box, offering essential functions for channel navigation, volume control, and basic menu access. Please read this manual thoroughly to ensure proper use and to maximize your remote control's functionality.
Product Overview
Figure 1: Anderic OEM Xfinity/Comcast DTA Remote Control. This image displays the full remote control, featuring a black body with white and yellow buttons. Key buttons include Power, Set, Info, numeric keypad (0-9), Enter, Last, Volume Up/Down, Mute, Channel Up/Down, and Language. The Xfinity logo is visible at the bottom.
Setup
1. Battery Installation
The remote control requires two (2) AA batteries (not included). Follow these steps to install them:
- Locate the battery compartment cover on the back of the remote control.
- Press down on the tab and slide the cover off.
- Insert two AA batteries, ensuring the positive (+) and negative (-) terminals align with the diagrams inside the compartment.
- Slide the battery cover back into place until it clicks securely.
2. Initial Use and Pairing
This Anderic remote is designed to be an OEM replacement and typically works with your Xfinity/Comcast Digital Transport Adapter (DTA) box without extensive programming. In most cases, it will function immediately after battery installation.
- Point the remote control directly at your DTA box.
- Press the POWER button. Your DTA box should respond.
- If the DTA box does not respond, ensure the batteries are correctly installed and the remote has a clear line of sight to the DTA.
For advanced programming or if your DTA requires specific pairing, refer to your Xfinity/Comcast DTA box's original manual or contact Xfinity/Comcast customer support for device-specific instructions. This remote is primarily for DTA box control and may not control your television directly without additional programming steps not covered here.
Operating Instructions
Familiarize yourself with the buttons on your remote control:
- POWER (Red Button): Turns the DTA box on or off.
- SET: Used for programming the remote, if required by your DTA model. Refer to your DTA manual for specific codes.
- INFO: Displays program information or current channel details.
- Numeric Keypad (0-9): Directly enter channel numbers.
- ENTER: Confirms selections or enters a channel number.
- LAST: Returns to the previously viewed channel.
- VOL +/-: Increases or decreases the volume.
- MUTE (Yellow Button): Silences the audio. Press again to restore audio.
- CH +/-: Changes the channel up or down.
- LANG: Changes the audio language track if available for the current program.
Maintenance
Battery Replacement
Replace batteries when the remote's performance degrades or if the indicator light (if present) flashes weakly or not at all. Always replace both batteries at the same time with new AA alkaline batteries. Do not mix old and new batteries, or different types of batteries.
Cleaning
To clean the remote control, use a soft, dry cloth. Do not use liquid cleaners, abrasive pads, or chemical solvents, as these can damage the remote's surface or internal components.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Remote not responding to DTA box. |
|
|
| Remote controls DTA but not TV volume/power. |
|
|
| Buttons are sticky or unresponsive. |
|
|
Specifications
- Brand: Anderic
- Compatible Devices: Digital Transport Adapter (DTA)
- Model Numbers: RC2392101/03B, RC2392101/01B (also known as tyyjmv-479)
- Power Source: 2 x AA Batteries (not included)
- Color: Black
- Special Feature: Ergonomic design
- Item Weight: 3.52 ounces (approximately 99.8 grams)
- Package Dimensions: 6.5 x 2.83 x 0.94 inches (approximately 16.5 x 7.2 x 2.4 cm)
Warranty Information
Specific warranty details for this Anderic product may vary. Please retain your proof of purchase. For information regarding warranty coverage, terms, and conditions, please contact the retailer or the manufacturer directly. Warranty claims typically require the original purchase receipt.
Customer Support
If you encounter issues not covered in this manual or require further assistance, please contact:
- The retailer from whom you purchased the remote control.
- Anderic Customer Service (refer to Anderic Store on Amazon for contact information, if available).
- Your Xfinity/Comcast service provider for DTA box specific support.