Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your EVIL ENERGY 6AN Fuel Line Kit. This kit features an AN6 braided nylon fuel hose made with a CPE rubber inner, a 304 steel wire layer, and a nylon outer braid, designed for various fluid transfer applications in automotive systems.
Product Features
- Size: ID of 6AN fuel hose: 0.31" (8mm), OD: 0.56" (14.3mm). Length: 10ft.
- Parameters: Working pressure: 750psi, Burst pressure: 2250psi; Temperature range: -22°F to 248°F (-30°C to 120°C); Minimum bending radius: 2.5 inches (63.5mm).
- Application: Compatible with transmission fluid, oil, race gas, and fuel, among others.
- Material: Constructed with a CPE rubber inner, reinforced with a layer of 304 steel wire, and protected by a nylon outer braid.
- Compatibility: The braided fuel hose is compatible with transmission fluid, oil, race gas, vacuum, hydraulic fluid, diesel, and various fuels.
Specifications
| Attribute | Value |
|---|---|
| Brand | EVIL ENERGY |
| Material | Nylon, Rubber, Stainless Steel |
| Color | Black |
| Product Dimensions | 120"L x 0.54"W |
| Item Weight | 0.82 Kilograms (1.8 pounds) |
| Maximum Pressure | 2250 PSI (Burst), 750 PSI (Working) |
| Outside Diameter | 0.54 Inches (14.3mm) |
| Item Length | 10 Feet |
| Manufacturer Part Number | FBA-KT00398BB |
Setup and Installation
Proper installation is crucial for the performance and longevity of your fuel line kit. Follow these steps carefully:
1. Prepare the Hose
Before cutting, wrap the desired cut area of the hose tightly with electrical tape to prevent fraying of the nylon braid. Use a high-speed saw or an angle grinder with a cutting wheel for a clean cut. After cutting, ensure the inside of the hose is clear of any debris.
Image: Hose preparation showing taping and a clean cut.
2. Assemble the Fittings
The fittings are designed for a secure connection. Unlike some lines that push and twist, these fittings require you to work the hose around and push it into the fitting. Apply a lubricant like petroleum jelly or light grease to the hose end to facilitate easier insertion into the adapter. Carefully thread the fitting onto the hose, ensuring the nylon braid does not fray excessively. Clean any frayed edges as needed.
Image: Step-by-step guide for assembling the hose with the AN fittings.
3. Final Connection
Once the fittings are securely attached to the hose, connect the fuel line to your system. Ensure all connections are tight to prevent leaks. Double-check the working pressure and temperature of your system against the product specifications before operation.
Image: Examples of the fuel line kit installed in an engine bay, demonstrating typical applications.
Operating
After installation, perform a thorough check for any leaks before operating the vehicle. Start the engine and allow it to run for a few minutes, observing all connections for signs of fluid seepage. The hose is designed to handle specified working pressures and temperatures; ensure your system operates within these limits.
Maintenance
Regular inspection of your EVIL ENERGY fuel line kit is recommended to ensure continued safe operation. Periodically check the entire length of the hose and all fittings for:
- Signs of wear, abrasion, or damage to the outer nylon braid.
- Any signs of fluid leaks around the fittings or along the hose.
- Proper routing to avoid contact with hot engine components or sharp edges.
- Tightness of all connections.
Address any issues promptly to prevent potential hazards.
Troubleshooting
- Leaks at Fittings: Ensure fittings are properly assembled and tightened. Re-check the hose insertion into the fitting. If fraying occurred during assembly, it might compromise the seal. Disassemble, re-cut, and reassemble if necessary.
- Hose Damage: If the hose shows signs of cuts, abrasions, or excessive wear, it must be replaced immediately. Do not attempt to repair damaged sections of the hose.
- Fluid Compatibility Issues: While the hose is broadly compatible, ensure the specific fluid being used is within the recommended temperature and pressure ranges and does not react adversely with CPE rubber or nylon.
Warranty and Support
For any questions regarding the EVIL ENERGY 6AN Fuel Line Kit, including warranty information or technical support, please contact EVIL ENERGY directly through their official channels or the retailer from whom the product was purchased. Keep your purchase receipt for warranty claims.
