1. Introduction
This manual provides detailed instructions for the proper installation, use, and maintenance of your SKS Velo 65 Mountain 29" Protective Plate Set. This product is designed to protect riders from water and debris when cycling on mountain bikes with 29-inch wheels.
Image 1.1: SKS Velo 65 Mountain 29" Protective Plate Set, showing both front and rear mudguards.
2. Safety Information
- Ensure all components are securely fastened before each ride. Loose parts can cause instability and potential hazards.
- Do not modify the product. Modifications may compromise its integrity and performance.
- Regularly inspect the mudguards and mounting hardware for signs of wear, damage, or corrosion. Replace damaged parts immediately.
- Maintain proper clearance between the mudguards and tires to prevent rubbing, especially during turns or over bumps.
3. Package Contents
Verify that all the following components are included in your package:
- Front Mudguard (1x)
- Rear Mudguard (1x)
- Metal Stays (2 pairs, for front and rear)
- Mounting Brackets (various types for fork crown, seat stay bridge, and frame eyelets)
- Assorted Bolts, Washers, and Nuts for installation
Image 3.1: Example of mounting brackets, bolts, and nuts included in the set.
4. Setup and Installation
Follow these steps to properly install your SKS Velo 65 Mountain 29" Protective Plate Set. Tools required (not included): Allen keys, wrenches.
4.1. Prepare Mounting Points
Identify the mounting points on your bicycle frame. For the front mudguard, locate the hole on the fork crown. For the rear mudguard, locate the hole on the seat stay bridge. Additionally, identify the eyelets near the front and rear wheel axles for attaching the metal stays.
4.2. Attach Main Brackets
- Front Mudguard Bracket: Secure the appropriate mounting bracket to the fork crown using a bolt and nut. Ensure it is firmly tightened.
- Rear Mudguard Bracket: Secure the appropriate mounting bracket to the seat stay bridge using a bolt and nut. Ensure it is firmly tightened.
Image 4.1: Step-by-step diagram for attaching the main brackets to the front fork crown and rear seat stay bridge.
4.3. Attach Stays to Frame
- Attach the ends of the metal stays to the frame eyelets located near the front and rear wheel axles. Use the provided bolts and nuts, ensuring a secure fit.
Image 4.2: Diagram illustrating the attachment of the metal stays to the bicycle frame eyelets.
4.4. Connect Mudguards to Brackets and Stays
- Front Mudguard: Slide the front mudguard onto the bracket previously installed on the fork crown.
- Rear Mudguard: Slide the rear mudguard onto the bracket previously installed on the seat stay bridge.
- Connect Stays: Align the mudguards with the free ends of the metal stays. Push the mudguards onto the stays until they click securely into place.
- Adjust Clearance: Adjust the length and angle of the stays to ensure adequate clearance between the mudguards and the tires. The mudguards should not rub against the tires or any other part of the bicycle.
Image 4.3: Close-up view of the click-in mechanism for attaching the mudguard to the metal stay.
Image 4.4: The SKS Velo 65 Mountain Protective Plate Set fully installed on a 29-inch mountain bike.
5. Operating the Product
The SKS Velo 65 Mountain Protective Plate Set functions passively by deflecting water, mud, and debris away from the rider and bicycle components. Once correctly installed and adjusted, no further operational input is required during riding. Ensure the mudguards remain free of obstructions and maintain proper clearance from the tires.
6. Maintenance
- Cleaning: Clean the mudguards regularly with water and a mild soap solution. Avoid abrasive cleaners or solvents that could damage the plastic material.
- Inspection: Periodically check all mounting bolts, nuts, and stay connections for tightness. Vibrations from riding can cause fasteners to loosen over time.
- Damage Check: Inspect the mudguards for cracks, bends, or other damage. Replace any damaged components to ensure continued effectiveness and safety.
7. Troubleshooting
- Rattling Noise: If the mudguards rattle during riding, check all mounting points and stay connections for tightness. Adjust the stays to ensure they are not vibrating against the frame or other components.
- Tire Rubbing: If the mudguards rub against the tires, loosen the stay connections and adjust their length or angle to increase clearance. Ensure the mudguard is centered over the tire.
- Inadequate Protection: If the mudguards are not effectively deflecting spray, check their angle and position. They may need to be adjusted closer to the tire (while maintaining clearance) or repositioned to cover more of the wheel.
8. Specifications
| Feature | Specification |
|---|---|
| Model Number | SKMVEL6529B |
| Wheel Size Compatibility | 29 inches |
| Recommended Tire Width | 2.0" - 2.35" |
| Material | Plastic |
| Color | Monochrome (Black) |
| Weight (without mounting material) | 290 g |
| Front Mudguard Length | 700 mm |
| Rear Mudguard Length | 930 mm |
| Product Dimensions (overall) | 83.82 x 20.32 x 10.16 cm |
Image 8.1: Diagram illustrating key specifications including wheel size, tire width, weight, and mudguard lengths.
9. Warranty and Support
For warranty information or technical support, please refer to the official SKS website or contact your local SKS dealer. Keep your proof of purchase for any warranty claims.
