Optimus H-8014 Infrared Quartz Heater User Manual

Introduction

Thank you for choosing the Optimus H-8014 Infrared Quartz Heater. This manual provides important information for the safe and efficient operation of your new heater. Please read it thoroughly before use and retain it for future reference.

The Optimus H-8014 is a portable infrared quartz heater designed to provide supplemental heat to indoor spaces. It features multiple heat settings, an energy-saving ECO mode, an LED display, and convenient push-button controls, along with a remote control for ease of use. Safety features include an internal heat limiting thermostat, overheat thermal cut-off, and a tip-over safety switch.

Important Safety Instructions

When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:

1. Read all instructions before using this heater.
2. This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Use handles when moving this heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9 m) from the front of the heater and keep them away from the sides and rear.
3. Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended.
4. Always unplug heater when not in use.
5. Do not operate any heater with a damaged cord or plug or after the heater malfunctions, has been dropped or damaged in any manner. Return heater to authorized service facility for examination, electrical or mechanical adjustment, or repair.
6. Do not use outdoors.
7. This heater is not intended for use in bathrooms, laundry areas, and similar indoor locations. Never locate heater where it may fall into a bathtub or other water container.
8. Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Arrange cord away from traffic area and where it will not be tripped over.
9. To disconnect heater, turn controls to OFF, then remove plug from outlet.
10. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater.
11. To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, where openings may become blocked.
12. A heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint, or flammable liquids are used or stored.
13. Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
14. This heater includes an overheat thermal cut-off and a tip-over safety switch for enhanced safety. If the heater tips over or overheats, it will automatically shut off.
15. Always plug heaters directly into a wall outlet/receptacle. Never use with an extension cord or relocatable power tap (outlet/power strip).

Setup

Unpacking

Carefully remove the heater from its packaging. Retain the packaging for off-season storage. Inspect the heater for any signs of damage. If the heater appears damaged, do not use it and contact customer support.

Placement

• Place the heater on a firm, level surface.
• Ensure there is at least 3 feet (0.9 m) of clear space around the front, sides, and rear of the heater to prevent fire hazards.
• Do not place the heater on soft surfaces like rugs or carpets that could block air vents.
• This heater is for indoor use only. Do not use it in wet or damp locations.

Power Connection

Plug the heater directly into a 120V AC, 60Hz electrical outlet. The heater is equipped with a 3-prong grounded plug. Do not use an adapter or extension cord. Ensure the outlet is in good condition and not loose.

Operating Instructions

The Optimus H-8014 heater can be operated using the control panel on the unit or the included remote control.

Control Panel and LED Display

The front panel features push-button controls and an LED display for easy operation and monitoring.

Powering On/Off

• Ensure the main power switch located on the rear of the unit is in the ON position.
• Press the POWER button on the control panel or remote control to turn the heater ON. The LED display will illuminate.
• Press the POWER button again to turn the heater OFF.

Heat Settings

The heater offers three heat settings: ECO, 1000W, and 1500W.

• Press the MODE button repeatedly to cycle through the heat settings: HIGH (1500W), LOW (1000W), and ECO (500W).
• The corresponding indicator light on the LED display will show the selected mode.
• In ECO mode, the heater automatically adjusts its power output to maintain the set temperature, optimizing energy consumption.

Thermostat Control

The automatic thermostat allows you to set a desired room temperature between 59°F and 86°F (15°C to 30°C).

• When the heater is ON, use the + and - buttons on the control panel or remote control to adjust the desired temperature.
• The LED display will show the set temperature.
• Once the room temperature reaches the set temperature, the heater will cycle ON and OFF to maintain it.

Timer Function

The timer allows you to set the heater to operate for a specific duration from 1 to 12 hours.

• Press the TIMER button on the control panel or remote control.
• Each press will increase the timer setting by one hour, up to 12 hours.
• The LED display will show the remaining hours.
• To cancel the timer, press the TIMER button until '00' is displayed, or turn the heater OFF.

Remote Control

The included remote control allows for convenient operation of all heater functions from a distance. Ensure the remote control has working batteries (not included, typically 2x AAA). Point the remote control directly at the heater's receiver window.

Maintenance

Regular maintenance helps ensure the longevity and efficient operation of your heater.

Cleaning

• Always unplug the heater and allow it to cool completely before cleaning.
• Use a soft, damp cloth to wipe the exterior surfaces of the heater. Do not use abrasive cleaners or solvents.
• Gently vacuum the air intake and exhaust grilles to remove dust and lint buildup. Do not allow water to drip into the heater housing.
• Never immerse the heater in water.

Storage

• Store the heater in a cool, dry location when not in use.
• It is recommended to store the heater in its original packaging to protect it from dust and damage.

Troubleshooting

If your heater is not operating correctly, please refer to the following common issues and solutions:

If the problem persists after trying these solutions, please contact Optimus customer support.

Specifications

Warranty Information

This Optimus H-8014 Infrared Quartz Heater comes with a 3-year manufacturer's warranty. This warranty covers defects in materials and workmanship under normal use. Please retain your proof of purchase for warranty claims.

For specific details regarding warranty terms, conditions, and service procedures, please refer to the warranty card included with your product or contact Optimus customer support.

Customer Support

If you have any questions about your Optimus H-8014 Infrared Quartz Heater, require technical assistance, or need to make a warranty claim, please contact Optimus customer support.

Please have your model number (H-8014) and proof of purchase ready when contacting support.

Contact information can typically be found on the manufacturer's website or on the product packaging.