1. Introduction
The LEONLITE Motion Sensor 4FT LED Utility Shop Light is designed to provide efficient and bright illumination for various indoor spaces. This 40W fixture delivers 4000 lumens of 5000K daylight, making it suitable for garages, workshops, laundry rooms, and other utility areas. Equipped with an integrated motion sensor, the light automatically activates upon detecting movement, offering hands-free operation and energy savings. Its linkable design allows for connecting multiple units to cover larger areas effectively.
Figure 1: LEONLITE Motion Sensor 4FT LED Utility Shop Light (Pack of 2)
2. Safety Information
Please read and understand all instructions before installing or operating this fixture. Retain this manual for future reference.
- Electrical Safety: Ensure power is turned off at the circuit breaker before installation or maintenance. All wiring connections must be in accordance with local and national electrical codes.
- Installation: This product is intended for indoor use only. Do not install in wet locations or areas with excessive humidity.
- Handling: Do not look directly into the LED light source when illuminated. Avoid touching the fixture when it is operating, as it may be hot.
- Damage: Do not operate the fixture if it is damaged. Contact customer support for assistance.
3. Setup and Installation
The LEONLITE Motion Sensor 4FT LED Utility Shop Light offers two primary installation methods: suspended mounting and surface mounting. All necessary hardware is included for both options.
3.1 Package Contents
Figure 2: Included mounting hardware and power cord.
Verify that all components are present before beginning installation:
- LED Shop Light Fixture(s)
- Power Cord (4.92ft)
- Hanging Chains
- S-Hooks
- Eye Hooks with Plastic Anchors (for suspended mounting)
- Screws (for surface mounting)
3.2 Installation Methods
Refer to the diagram below for visual guidance on both suspended and surface mounting.
Figure 3: Step-by-step installation guide for both mounting types.
Suspended Mounting:
- Step 1: Mount eye hooks to the ceiling using plastic anchors.
- Step 2: Install S-hooks into the end of the hanging chains.
- Step 3: Install S-hooks into the end cap of the LED lamp.
- Step 4: Attach the assembled components to the eye hooks.
Surface Mounting:
- Step 1: Secure the screws to the ceiling, aligning with the 'Church key' holes on the fixture.
- Step 2: Lock the fixture to the ceiling by sliding it onto the screws.
- Step 3: Connect the power and turn on the fixture.
3.3 Linkable Design
Up to 4 units of this LED shop light can be linked together from a single power source. This allows for extended lighting coverage without additional wiring. Simply connect the power cord of one fixture to an outlet, and then use the provided linking cable (or an additional power cord) to connect subsequent fixtures in a series.
Figure 4: Illustration of the extendable design, linking multiple units.
3.4 Installation Video
Video 1: Official LEONLITE overview of the 4FT Motion Activated LED Shop Light, demonstrating features and installation.
4. Operating Instructions
The LEONLITE Motion Sensor LED Shop Light features an integrated motion sensor for automatic operation.
- Motion Detection: The built-in motion sensor detects movement within a 16.4ft radius. Upon detection, the light will automatically turn on.
- Automatic Shut-off: Once activated, the light will remain on for approximately 10 minutes. If no further motion is detected within this period, the light will automatically turn off to conserve energy. The timer resets with each new motion detection.
- Hands-Free Operation: No manual switch is required for daily use, providing convenience in busy environments.
Figure 5: Motion sensor detection range and auto-off feature.
5. Maintenance
Regular maintenance ensures optimal performance and longevity of your LED shop light.
- Cleaning: Disconnect power before cleaning. Use a soft, dry cloth to wipe the fixture. Do not use abrasive cleaners or solvents, as they may damage the finish or electrical components.
- Inspection: Periodically check the power cord and connections for any signs of wear or damage. Ensure mounting hardware remains secure.
- LED Lifespan: The integrated LED chips have an estimated lifespan of 50,000 hours, reducing the need for frequent bulb replacements.
6. Troubleshooting
If you encounter issues with your LEONLITE Motion Sensor LED Shop Light, refer to the following common solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on. | No power supply. Motion sensor not triggered. | Check power connection and circuit breaker. Ensure motion is within the detection range. |
| Light turns off too quickly. | No continuous motion detected. | Ensure continuous motion within the detection range to reset the 10-minute timer. |
| Light flickers or buzzes. | Loose connection. Electrical interference. | Check all electrical connections. Ensure proper grounding and minimize interference from other devices. |
If the problem persists after attempting these solutions, please contact customer support.
7. Specifications
| Feature | Detail |
|---|---|
| Brand | LEONLITE |
| Model Number | XL1SL-40W50-MSS |
| Wattage | 40 watts |
| Brightness | 4000 Lumens |
| Light Color | Daylight (5000K) |
| Voltage | 120 Volts |
| Product Dimensions | 49.6"L x 2.95"W x 5.51"H |
| Material | Metal plate, Polycarbonate |
| Lifespan | 50,000 hours |
| Motion Sensor Range | 16.4ft radius |
| Auto-off Time | 10 minutes (after no motion) |
| Linkable Units | Up to 4 units |
| Certifications | ETL Qualified, FCC Certified |
8. Warranty and Support
This LEONLITE product is backed by a 3-year warranty, ensuring reliability and performance. For technical support, troubleshooting assistance, or warranty claims, please contact LEONLITE customer service. Keep your purchase receipt as proof of purchase.
