System Sensor RTS151

Download PDFFree PDF. The Save button below keeps a bookmark and private notes in your account.

System Sensor RTS151 Remote Test Station User Manual

Model: RTS151 | Brand: System Sensor

Product Overview

The System Sensor RTS151 is a remote test station designed for use with compatible System Sensor devices. It provides a convenient point for testing and monitoring system functionality without direct access to the primary device. This manual provides essential information for the proper setup, operation, and maintenance of your RTS151 unit.

Front view of the System Sensor RTS151 Remote Test Station, showing a rectangular white unit with three recessed sections and two visible screws.

Figure 1: System Sensor RTS151 Remote Test Station. This image displays the front of the device, which is a white, rectangular unit. It features three distinct recessed sections running vertically down its center, designed to accommodate test points or indicators. Two screws are visible, one near the top and one near the bottom, securing the faceplate. The overall design is clean and functional, typical of industrial control equipment.

Setup and Installation

Proper installation is crucial for the reliable operation of the RTS151. Always refer to local codes and the specific installation instructions for the System Sensor device it will be connected to.

  1. Mounting Location: Select a suitable location for the remote test station, typically near the primary device or in an accessible area for testing. Ensure the mounting surface is flat and stable.
  2. Wiring: Connect the RTS151 to the compatible System Sensor control panel or device according to the wiring diagram provided with the primary device. Pay close attention to polarity and terminal designations. Use appropriate gauge wiring.
  3. Secure Mounting: Securely mount the RTS151 to the chosen surface using appropriate fasteners. Ensure it is firmly attached and does not wobble.
  4. Power Up: Once all connections are made and verified, power up the system. Observe any indicator lights on the RTS151 or the primary device to confirm proper initialization.

Note: Installation should only be performed by qualified personnel in accordance with all applicable national and local codes.

Operating Instructions

The RTS151 provides remote testing capabilities for connected System Sensor devices. The specific test procedures will depend on the primary device it is connected to.

  • Initiating a Test: To initiate a test, follow the instructions provided in the manual for the primary System Sensor device. This typically involves activating a test switch or button on the RTS151 or the primary control panel.
  • Observing Indicators: During a test, observe the indicator lights on the RTS151. These lights provide visual feedback on the status of the test and the connected device. Refer to the primary device's manual for the meaning of specific light patterns (e.g., green for normal, red for alarm/fault).
  • Resetting the System: After a successful test or if an alarm/fault condition is indicated, reset the system according to the primary device's instructions. This may involve pressing a reset button on the RTS151 or the control panel.

For detailed operational procedures, always consult the user manual of the System Sensor device connected to the RTS151.

Maintenance

The RTS151 is designed for minimal maintenance. Regular inspection is recommended to ensure continued proper operation.

  • Cleaning: Periodically clean the exterior of the unit with a soft, dry cloth. Do not use abrasive cleaners or solvents.
  • Visual Inspection: Annually, or as required by local codes, visually inspect the unit for any signs of physical damage, loose connections, or excessive dust accumulation.
  • Functional Testing: Perform routine functional tests as recommended by the primary system's maintenance schedule to ensure the RTS151 is communicating correctly and initiating tests as expected.

Troubleshooting

If you encounter issues with your RTS151, consider the following common troubleshooting steps:

ProblemPossible CauseSolution
No response from RTS151 during test.
  • Incorrect wiring.
  • No power to primary system.
  • Faulty primary device connection.
  • Verify all wiring connections according to the primary device's manual.
  • Ensure the primary system is powered on.
  • Check connections at the primary device.
Indicator lights not functioning.
  • Loose internal connection.
  • Unit malfunction.
  • Inspect internal connections (if accessible and safe to do so, otherwise contact support).
  • If problem persists, contact System Sensor technical support.

If troubleshooting steps do not resolve the issue, contact System Sensor technical support or a qualified service technician.

Specifications

AttributeDetail
ModelRTS151
BrandSystem Sensor
Package Dimensions6 x 4 x 3 inches
Item Weight1 pounds
ASINB077412M7H
Date First AvailableApril 14, 2014
ManufacturerSystem Sensor

Warranty and Support

For warranty information and technical support, please refer to the official System Sensor website or contact their customer service directly. Warranty terms and conditions may vary based on region and purchase date.

It is recommended to register your product with System Sensor to receive updates and support.

© 2024 System Sensor. All rights reserved.

This manual is for informational purposes only. System Sensor reserves the right to change specifications without notice.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.