Graco FinishPro HVLP 7.0 Standard Sprayer User Manual

1. Safety Information

WARNING: To reduce the risk of injury, the user must read and understand this instruction manual before using this product.

• Avoid eye contact with spray.
• Use in a well-ventilated area.
• Wear appropriate protective gear, including eye protection, gloves, and a respirator.
• Dispose of chemicals and materials properly according to local regulations.
• Always disconnect power before cleaning or performing maintenance.
• Ensure all connections are secure before operation.

2. Product Overview

The Graco FinishPro HVLP 7.0 Standard Sprayer (Model 17N263) is designed for precise application of various coatings, offering control and a high-quality finish. Key features include:

• Ultimate Control: Ideal for projects requiring fine finish.
• Needle System: Includes a #3 size (1.3mm) needle, suitable for lacquers, stains, enamels, epoxies, urethane, and varnish. Needles are easily interchangeable.
• FlexLiner Bag System: Designed for lighter weight, easy cleanup, and ability to spray in any direction, including upside down. Facilitates quick color changes.
• Super-Flex Air Hose: 15% lighter than comparable hoses for improved control.
• TurboControl System: Allows adjustment of the TurboForce turbine speed to match performance requirements.
• EDGE II Gun: Features a 75% lighter trigger pull with EasyGlide technology.
• Standard Filtration System: Washable filter extends motor life and ensures a quality finish.

Figure 2.1: Graco FinishPro HVLP 7.0 Standard Sprayer unit.

Figure 2.2: The EDGE II Spray Gun with the FlexLiner cup system.

3. Setup

3.1 Unpacking and Inspection

1. Carefully remove all components from the packaging.
2. Inspect all parts for any damage that may have occurred during shipping. Do not operate if damaged.
3. Verify all components listed in the "What's in the Box" section are present.

3.2 Assembly

1. Connect the Super-Flex Air Hose to the HVLP unit and the EDGE II spray gun. Ensure connections are tight.
2. Attach the FlexLiner cup to the spray gun.
3. Select the appropriate needle for your material. The #3 (1.3mm) needle is included for fine finishes.
4. Ensure the filter is clean and properly installed in the unit.

Figure 3.1: The compact design allows for easy transport of the unit.

4. Operating Instructions

4.1 Material Preparation

1. Ensure your coating material is properly mixed and free of debris.
2. Pour the prepared material into the FlexLiner bag within the cup. Do not overfill.

4.2 Adjusting Settings

1. Turn on the HVLP unit.
2. Use the TurboControl System dial to adjust the turbine speed. Higher speeds are generally for thicker materials or faster application.
3. Adjust the material flow knob on the EDGE II gun to control the amount of material being sprayed.
4. Test the spray pattern on a scrap piece of material to ensure desired coverage and finish.

Figure 4.1: Adjust the material flow and air cap for optimal spray pattern.

4.3 Spraying Technique

• Maintain a consistent distance from the surface (typically 6-10 inches).
• Move the gun in smooth, even passes, overlapping each pass by about 50%.
• Release the trigger at the end of each pass to avoid excessive material buildup.
• The FlexLiner system allows spraying at various angles, including upside down, for hard-to-reach areas.

Figure 4.2: Maintain consistent motion for an even finish.

Figure 4.3: The FlexLiner system enables spraying in any direction, including upside down.

4.4 Changing Needles and Colors

• To change needles, ensure the unit is off and depressurized. Follow the gun's instructions for needle removal and insertion.
• For quick color changes, remove the current FlexLiner bag and replace it with a new one containing the desired color. This minimizes cleanup between colors.

Figure 4.4: Needles can be changed with a simple click mechanism.

4.5 Official Product Videos

5. Maintenance

5.1 Cleaning the Sprayer

1. After each use, disconnect the power.
2. Remove the FlexLiner bag and dispose of any remaining material properly.
3. Clean the spray gun thoroughly with appropriate cleaning solution (water for latex, solvent for oil-based paints).
4. Clean the needle and air cap.
5. Rinse the FlexLiner cup if reusing, or dispose of it.
6. Clean the exterior of the HVLP unit.

5.2 Filter Maintenance

• Regularly inspect the standard filtration system filter.
• Clean the washable filter as needed to maintain optimal airflow and prevent motor strain.
• Replace the filter if it shows signs of damage or excessive wear.

6. Troubleshooting

7. Specifications

• Model Name: FinishPro HVLP 7.0 Standard Series
• Model Number: 17N263
• Brand: Graco
• Tank Volume: 1 Quart
• Color: Blue
• Material: Urethane
• Item Weight: 18 Pounds
• Hose Length: 240 Inches (20 ft)
• Power Source: Electric (120V AC, 11 A)
• Max. Pressure: 7 psi
• Nozzle Size: 1.3mm / 0.051 in (#3 needle)
• Max. Flow: 65 cfm
• Pattern Size: 1/4 in to 12 in
• Included Components: Instruction Guide, EDGE II Spray Gun
• Dimensions (W x H): 13.25"W x 14"H

Figure 7.1: Approximate dimensions of the HVLP unit.

8. Warranty and Support

The Graco FinishPro HVLP 7.0 Standard Sprayer comes with a 3-year limited warranty. For warranty claims, technical support, or replacement parts, please refer to the contact information provided in the included Instruction Guide or visit the official Graco website.

Return Policy: This product is eligible for a 30-day refund/replacement policy from the seller (Amazon).