Introduction
This manual provides essential instructions for the safe and effective use of your IEKOV High Voltage RGB LED Light Strip 4-Pin Connectors and End Caps. These components are designed specifically for IEKOV High Voltage RGB LED Light Strips to ensure proper electrical connection and insulation. Please read this manual thoroughly before installation and retain it for future reference.
What's in the Box
Your package should contain the following items:
- 10 pieces of RGB 4-pin connectors
- 10 pieces of End Caps

This image presents both the 4-pin connectors and end caps, illustrating the complete set of components included for securing and connecting high voltage RGB LED light strips.
Safety Information
Please observe the following safety precautions:
- High Voltage Warning: This product is designed for high voltage LED light strips. Always ensure the power supply is disconnected before handling or installing any components to prevent electric shock.
- Compatibility: These connectors and end caps are specifically for IEKOV High Voltage RGB LED Light Strips. Do not use them with other brands or types of LED strips unless explicitly stated as compatible.
- Indoor Use: This product is rated for indoor use only. Avoid exposure to moisture or outdoor elements unless the entire light strip system is rated for outdoor use and properly sealed.
- Professional Installation: If you are unsure about any step of the installation process, consult a qualified electrician.
- Proper Sealing: Ensure end caps are securely fitted to prevent moisture ingress and electrical hazards.
Setup and Installation
Follow these steps to properly install the 4-pin connectors and end caps with your IEKOV High Voltage RGB LED Light Strip:

This detailed diagram provides a step-by-step visual guide for installing the high voltage RGB LED light strip, including cutting, connecting pins, applying end caps, and securing the strip.
- Step 1: Cut the Strip Light
Cut the LED strip light according to your desired length. Ensure you cut only at the designated cut marks (typically indicated by a scissor icon or copper pads). The strip light can only be cut in meters. - Step 2: Connect the Strip Light and Power Plug
Insert the 4-pin connector into the end of the cut strip light, aligning the pins with the corresponding contacts on the strip. For RGB multi-colored strips, ensure correct pin alignment. Then, connect the adapter cable or power plug to the 4-pin connector. - Step 3: Block Up the End of Strip Light with End Cap
Block the end of the strip light (the opposite end from the power connection) with an end cap. This prevents short circuits. Apply a sufficient amount of waterproof insulation glue around the end cap and the blocked end of the strip light to ensure a secure and waterproof seal. - Step 4: Fix the Strip Light with Fixed Buckles
Secure the LED strip light in place using fixed buckles. It is recommended to use at least one fixed buckle per meter to ensure stability. Once secured, you can turn on the power supply. - Step 5: Operating RGB Strip Light
For RGB strip lights, you can choose any colors or lighting modes by pressing the switch button on your controller or power plug.

This image displays the individual 4-pin connectors, essential for establishing electrical connections within the RGB LED light strip system.

This image shows the translucent end caps, designed to seal the ends of the LED light strips, providing protection and insulation.
Operating Instructions
Once the 4-pin connectors and end caps are correctly installed and secured, the operation of the LED strip light is controlled by its power supply and/or controller. Ensure all connections are firm and sealed before powering on.
Maintenance
These components require minimal maintenance. Periodically inspect the connections and end caps for any signs of wear, damage, or compromised sealing. If any issues are found, disconnect power immediately and replace or re-seal the affected components as necessary. Keep the connectors and end caps clean and free from dust or debris.
Troubleshooting
If your LED strip light is not functioning correctly after installation, consider the following:
- Lights Not Turning On:
The LED strip light is polarized. If the lights do not turn on when first plugged in, quickly unplug the power cord and flip the power connector 180 degrees, or insert the power connector into the opposite end of the strip light. Ensure the power supply is connected and functioning. - Flickering or Inconsistent Lighting:
Check all 4-pin connections to ensure they are secure and making proper contact. Verify that the power supply is adequate for the length of the LED strip. - Partial Lighting:
Inspect the strip for any damage or improper cuts. Ensure all pins of the connector are fully inserted and aligned with the strip's contacts. - Short Circuit:
If a short circuit occurs, immediately disconnect power. Check the end caps for proper sealing and ensure no exposed wires are touching. Re-apply waterproof insulation glue if necessary.
Specifications
| Component Type | 4-Pin Connectors and End Caps |
| Compatibility | IEKOV High Voltage RGB LED Light Strip |
| Quantity | 10 pieces of 4-pin connectors, 10 pieces of End Caps |
| Material | Plastic |
| Indoor/Outdoor Usage | Indoor |
| Model Number | RGB 4pins+End Cap |
Warranty and Support
For warranty information or technical support, please refer to the product packaging or contact IEKOV customer service directly. Keep your purchase receipt as proof of purchase.