Introduction
Thank you for choosing the Project Source 2-Pack 7.4-in W White LED Flush Mount Light. This manual provides essential information for the safe installation, operation, and maintenance of your new lighting fixtures. Please read this manual thoroughly before installation and retain it for future reference.
These LED flush mount ceiling lights are designed for both indoor and outdoor living spaces, featuring a wet-rated design. They are Energy Star rated for efficiency, provide a color temperature of 3000K, a Color Rendering Index (CRI) of 90, and an output of 730 lumens.
Safety Information
Always follow basic safety precautions when installing or working with electrical fixtures to reduce the risk of fire, electric shock, or personal injury.
- WARNING: Risk of electric shock. Disconnect power at the fuse or circuit breaker before installing or servicing.
- WARNING: Risk of fire. Use only in circuits rated for the fixture.
- Consult a qualified electrician if you are unsure about the installation process.
- Do not modify the fixture in any way. Any modifications may void the warranty and create a safety hazard.
- Ensure all connections are secure and properly insulated.
- Do not install near heat sources or in areas with excessive moisture beyond its wet-rated capabilities.
- This product is designed for direct wire connection and does not use a plug.
What's in the Box
Verify that all components are present before beginning installation:
- 2 x Project Source 7.4-in LED Flush Mount Light Fixtures
- Mounting Hardware
- Remote Control (Note: While the product data mentions a remote control, typical flush mount lights of this type do not include one. Please verify your specific package contents.)
Setup (Installation)
Installation should be performed by a qualified individual. Always ensure power is disconnected at the circuit breaker before starting.
- Turn Off Power: Locate the circuit breaker controlling the light fixture's location and turn it off. Verify power is off using a voltage tester.
- Prepare Mounting Surface: Ensure the electrical box is securely mounted and capable of supporting the fixture's weight.
- Connect Wires: Connect the fixture's wires to the corresponding house wires using wire nuts (typically black to black, white to white, and ground to ground). Ensure all connections are tight and secure.
- Mount Fixture: Carefully align the fixture with the mounting holes on the electrical box and secure it using the provided mounting hardware.
- Restore Power: Once the fixture is securely installed, restore power at the circuit breaker.
Image: Two Project Source 7.4-inch white LED flush mount ceiling lights, showcasing their compact and low-profile design suitable for various indoor and outdoor applications.
Operating Instructions
The Project Source LED Flush Mount Light operates like a standard ceiling light fixture. Once properly installed and power is restored, it can be controlled via a standard wall switch.
- Turning On/Off: Flip the wall switch connected to the fixture to turn the light on or off.
- Energy Efficiency: As an Energy Star rated LED fixture, it consumes significantly less energy than traditional incandescent bulbs, providing long-term savings.
Maintenance
These LED fixtures require minimal maintenance due to their long lifespan. However, occasional cleaning is recommended to maintain optimal light output and appearance.
- Cleaning: Ensure power is off before cleaning. Use a soft, dry, or slightly damp cloth to wipe the surface of the fixture. Do not use abrasive cleaners or solvents, as they may damage the finish or electrical components.
- LED Longevity: The integrated LED light source is designed for long-term use and is not user-replaceable. If the LED fails, the entire fixture typically requires replacement.
Troubleshooting
If you encounter issues with your light fixture, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on. | No power to the fixture; loose wiring; faulty switch. | Check circuit breaker. Ensure all wire connections are secure. Test the wall switch. |
| Light flickers. | Loose wiring; incompatible dimmer switch (if applicable); power fluctuations. | Verify wire connections. Ensure the fixture is not connected to an incompatible dimmer. Consult an electrician for power issues. |
| Light output is dim or inconsistent. | Dust accumulation on diffuser; aging LED components. | Clean the diffuser. If the issue persists and the fixture is old, it may be reaching the end of its lifespan. |
| Fixture makes humming noise. | Loose mounting; electrical interference. | Ensure fixture is securely mounted. Consult an electrician if noise persists. |
Specifications
- Model Number: CLL56-2WW
- Product Dimensions: 7.4 x 7.4 x 1.4 inches
- Weight: 2.15 Pounds (per pack, total for 2 lights)
- Brand: Project Source
- Color: White
- Light Fixture Form: Ceiling (Flush Mount)
- Indoor/Outdoor Usage: Indoor/Outdoor (Wet Rated)
- Power Source: Corded Electric (Direct Wire)
- Light Output: 730 Lumens
- Color Temperature: 3000K
- Color Rendering Index (CRI): 90
- Energy Rating: Energy Star
Warranty and Support
Project Source products are manufactured to high-quality standards. For information regarding warranty coverage, technical support, or replacement parts, please contact Project Source customer service. Keep your purchase receipt as proof of purchase.
For assistance, please refer to the contact information provided on the product packaging or the official Project Source website.
