1. Introduction
This manual provides essential information for the safe and correct installation, operation, and maintenance of your Frigidaire STACKIT24 Front-Load Laundry Stacking Kit. Please read these instructions thoroughly before beginning installation and retain them for future reference.
1.1. Product Overview
The Frigidaire STACKIT24 stacking kit is designed to securely stack a compatible Frigidaire front-load dryer on top of a compatible Frigidaire front-load washer, optimizing space in your laundry area. This kit ensures stability and proper alignment between the two appliances.
1.2. Safety Information
- Always disconnect power to both the washer and dryer before installation.
- Ensure the washer is level and stable before stacking.
- Use appropriate lifting techniques or seek assistance when lifting the dryer onto the washer.
- Verify all components are securely fastened as per instructions to prevent tipping or movement.
- Do not modify the stacking kit or appliances. Use only genuine replacement parts if needed.
2. Package Contents
Carefully unpack the stacking kit and verify that all components are present. If any parts are missing or damaged, do not proceed with installation. Contact customer support for assistance.
- Cover
- Screw
Note: Actual package contents may vary. Please refer to the packing list included with your specific kit.
3. Setup and Installation
Follow these steps to properly install the Frigidaire STACKIT24 stacking kit and stack your laundry appliances.
3.1. Pre-Installation Checks
- Ensure both the washer and dryer are compatible with the STACKIT24 kit.
- Confirm the installation area has sufficient space and a stable, level floor.
- Disconnect power to both appliances.
3.2. Stacking Procedure
- Position the washer in its final location, ensuring it is level and stable.
- Carefully lift the dryer and place it centered on top of the washer. It is recommended to have at least two people for this step.
- Align the stacking kit components (e.g., cover, screws) with the designated attachment points on both the washer and dryer.
- Securely fasten all screws and components as instructed to ensure the dryer is firmly attached to the washer.
- Verify that the stacked appliances are stable and do not wobble.
Image 1: Example of a Frigidaire STACKIT24 Stacking Kit securing a dryer on top of a washer.
4. Operating Instructions
Once the stacking kit is installed, operate your washer and dryer according to their respective user manuals. The stacking kit itself does not require specific operational steps beyond ensuring proper installation.
- Always ensure the dryer door and washer door are closed before operation.
- Avoid placing heavy objects on top of the dryer, as this could affect stability.
- If you notice excessive vibration or instability during operation, immediately stop the appliances and re-check the stacking kit installation and appliance leveling.
5. Maintenance
Regular maintenance helps ensure the longevity and safety of your stacked laundry unit.
- Periodically check all screws and fasteners of the stacking kit to ensure they remain tight. Tighten if necessary.
- Inspect the stacking kit components for any signs of wear or damage. Replace damaged parts immediately.
- Clean the exterior of the stacking kit with a soft, damp cloth. Avoid abrasive cleaners.
6. Troubleshooting
If you encounter issues with your stacked laundry unit, refer to the following common troubleshooting steps.
6.1. Unit Wobbles or is Unstable
- Check Leveling: Ensure the washer is perfectly level. Adjust its leveling feet as needed.
- Verify Stacking Kit Installation: Confirm all stacking kit components are correctly installed and securely tightened.
- Load Distribution: Ensure laundry loads in both washer and dryer are balanced.
6.2. Unusual Noises
- Vibration: Excessive vibration can cause noise. Refer to the 'Unit Wobbles' section above.
- Loose Parts: Check if any stacking kit components have become loose. Tighten them if necessary.
7. Specifications
| Feature | Specification |
|---|---|
| Model Number | STACKIT24 |
| Product Dimensions (L x W x H) | 25.5 x 3.75 x 25.75 inches |
| Item Weight | 10 pounds |
| Finish Type | White |
| Material | Stainless Steel (components may vary) |
| Included Components | Cover, Screw |
8. Warranty and Support
This Frigidaire STACKIT24 Stacking Kit is covered by a manufacturer's limited warranty. Please refer to the warranty card included with your purchase for specific terms and conditions, including warranty period and coverage details.
8.1. Customer Support
For technical assistance, missing parts, or warranty inquiries, please contact Electrolux customer support. Contact information can typically be found on the manufacturer's website or in your product documentation.
