Introduction
Thank you for choosing the Artemide Crazy Wall/Ceiling Lamp, Model 1638020A. This manual provides essential information for the safe installation, operation, and maintenance of your new lighting fixture. Please read these instructions carefully before installation and retain them for future reference.
Important Safety Instructions
To ensure safe operation and prevent damage, always follow these precautions:
- Electrical Safety: Always disconnect power at the main circuit breaker before installing, servicing, or cleaning the fixture. Ensure all electrical connections comply with local codes and regulations. If you are unsure about wiring, consult a qualified electrician.
- Installation: This fixture is designed for wall or ceiling mounting. Ensure the mounting surface is structurally sound and can support the weight of the lamp (approximately 7 kg). Do not install in damp or wet locations.
- Handling: Handle the lamp with care. Avoid dropping or subjecting it to strong impacts.
- Integrated LED: This lamp features an integrated LED light source. Do not attempt to replace the LED bulbs yourself. Contact qualified service personnel if the light source requires attention.
- Cleaning: Use only a soft, dry cloth for cleaning. Avoid abrasive cleaners or solvents that may damage the finish or electrical components.
Package Contents
Verify that all components are present before beginning installation:
- Artemide Crazy Lamp (1 unit)
- Mounting hardware (screws, anchors)
- Instruction Manual (this document)
Setup and Installation
Installation should be performed by a qualified professional or a person with sufficient electrical knowledge.
Tools Required (Not Included)
- Screwdriver (Phillips head)
- Drill with appropriate drill bits
- Wire strippers
- Voltage tester
- Pencil and measuring tape
Mounting Instructions
- Turn off Power: Locate the circuit breaker controlling the light fixture's location and turn off the power. Verify power is off using a voltage tester.
- Prepare Mounting Surface: Mark the desired location for the lamp on the wall or ceiling. Use the mounting bracket as a template to mark drill holes.
- Drill Holes: Drill pilot holes at the marked locations. Insert wall anchors if necessary for secure mounting.
- Attach Mounting Bracket: Secure the mounting bracket to the wall or ceiling using the provided screws.
- Electrical Connection: Carefully connect the lamp's electrical wires to the household wiring. Typically, connect the live (black/brown) wire from the lamp to the live wire from the wall, the neutral (white/blue) wire from the lamp to the neutral wire from the wall, and the ground (green/yellow) wire to the ground wire. Ensure all connections are secure with wire nuts.
- Attach Lamp Fixture: Carefully align the lamp fixture with the mounting bracket and secure it in place using the provided screws. Ensure no wires are pinched.
- Restore Power: Once the lamp is securely installed and all connections are checked, restore power at the circuit breaker.
Image: The Artemide Crazy Wall/Ceiling Lamp, showcasing its design and taupe color. This image illustrates the general appearance of the product after installation.
Note on Videos: No official product installation videos were available from the seller for this model. Please refer to the detailed written instructions above.
Operating the Lamp
The Artemide Crazy Lamp is designed for simple operation.
- Turning On/Off: Operate the lamp using a standard wall switch connected to its electrical circuit.
- Light Source: The lamp features an integrated LED light source, providing consistent illumination.
Care and Maintenance
Proper care will ensure the longevity and appearance of your Artemide Crazy Lamp.
- Cleaning: Before cleaning, ensure the power to the fixture is turned off at the circuit breaker. Use a soft, dry, lint-free cloth to gently wipe the surface of the lamp. For stubborn marks, a slightly damp cloth may be used, followed immediately by a dry cloth.
- Avoid Chemicals: Do not use abrasive cleaners, solvents, or harsh chemicals, as these can damage the ABS/Polycarbonate/Technopolymer material and finish.
- Integrated LED: The LED light source is integrated and designed for a long lifespan. It does not require routine replacement. If the light source fails, contact customer support.
Troubleshooting
If you encounter issues with your lamp, refer to the following table for common problems and solutions.
| Problem | Possible Cause | Solution |
|---|---|---|
| Lamp does not light up. | No power supply. Loose electrical connection. Faulty wall switch. | Check if the circuit breaker is ON. Ensure all wire connections are secure (with power off). Test the wall switch or consult an electrician. |
| Light flickers. | Loose electrical connection. Incompatible dimmer switch (if applicable, though not specified for this model). | Check all electrical connections (with power off). Ensure the lamp is connected to a compatible circuit. |
| Lamp is damaged. | Physical impact. Manufacturing defect. | Discontinue use. Contact customer support for assistance. |
Technical Specifications
Detailed specifications for the Artemide Crazy Wall/Ceiling Lamp:
| Feature | Specification |
|---|---|
| Model Number | 1638020A |
| Brand | Artemide |
| Designer | Ernesto Gismondi |
| Dimensions (L x W x H) | 70 x 0.1 x 10 cm |
| Weight | 7 Kilograms |
| Material | ABS/Polycarbonate/Technopolymer, Acrylonitrile Butadiene Styrene |
| Color | Taupe (Shade color: White) |
| Mounting Type | Wall or Ceiling Mounting |
| Light Source Type | Integrated LED |
| Number of Light Sources | 1 |
| Wattage | 35 Watts |
| Luminous Efficacy | 3310 Lumens |
| Color Temperature | 2700 Kelvin |
| Energy Label | A++ |
| Power Source | Electric Cable |
| Manufacturer | Eden Illuminizione |
Warranty and Customer Support
Artemide products are manufactured to high-quality standards and are covered by a limited warranty against manufacturing defects. Please refer to the warranty card included with your purchase or visit the official Artemide website for detailed warranty terms and conditions.
For technical assistance, replacement parts, or any questions regarding your Artemide Crazy Lamp, please contact your authorized Artemide dealer or customer service department. Contact information can typically be found on the official Artemide website or on your purchase documentation.