1. Introduction
This manual provides essential instructions for the setup, operation, and maintenance of your Viper 7654V SuperCode SST 1-Way Companion Remote. Please read this guide thoroughly to ensure proper use and to maximize the functionality of your remote control system.
2. Product Overview
The Viper 7654V is a 1-way companion remote designed to work with compatible Viper security and remote start systems. It features a durable design with five rubberized buttons for various functions and an LED indicator for command confirmation.
Image 2.1: Viper 7654V SuperCode SST 1-Way Companion Remote. This image displays a black, oval-shaped remote control with five distinct rubberized buttons and a red LED indicator positioned at the top. A sturdy metal key ring is attached to the bottom right side of the remote.
3. Setup and Programming
To use your new Viper 7654V remote, it must be programmed to your vehicle's Viper security or remote start system. The programming procedure typically involves placing the vehicle's system into programming mode and then pressing a sequence of buttons on the new remote.
General Programming Steps (Consult your system's main unit manual for specific details):
- Locate the Valet Button: The valet button is usually located on the vehicle's dashboard or near the control module.
- Enter Programming Mode: Turn the ignition key to the ON position. Press and release the valet button a specific number of times (e.g., one, two, or three times) depending on the desired programming step. The system will typically chirp to confirm entry into programming mode.
- Program the Remote: While the system is in programming mode, press and hold the Lock button on your new 7654V remote until the system chirps again, confirming successful programming.
- Exit Programming Mode: Turn the ignition key to the OFF position or wait for the system to automatically exit programming mode.
If you encounter difficulties, refer to the installation manual of your Viper main control unit or contact a professional installer.
4. Operating Instructions
The Viper 7654V remote features five distinct buttons, each controlling a specific function of your vehicle's security or remote start system. The red LED at the top of the remote will illuminate to confirm that a command has been sent.
- Lock Button (Padlock icon): Press this button to arm your vehicle's security system and lock the doors.
- Unlock Button (Unlatched padlock icon): Press this button to disarm your vehicle's security system and unlock the doors.
- Remote Start/Stop Button (Circular arrow with a dot icon): Press and hold this button to remote start your vehicle. Press and hold again to remote stop the engine. (Functionality may vary based on system configuration).
- AUX Button (Text "AUX"): This button controls an auxiliary function, which can be programmed for various purposes such as trunk release, power windows, or other accessories. Consult your system's manual for the specific function assigned.
- Function/Panic Button (Stylized "f" icon): This button typically serves as a function button for advanced operations or can be used to activate the panic alarm by pressing and holding it.
For detailed information on specific button combinations and advanced features, refer to the complete user manual for your Viper security or remote start system.
5. Maintenance
Battery Replacement
The Viper 7654V remote control is powered by one CR2 battery. When the remote's range decreases or the LED indicator becomes dim, it is time to replace the battery.
- Open the Remote Casing: Carefully pry open the remote casing using a small flat-head screwdriver or a coin at the designated notch, usually located on the side or bottom edge.
- Remove Old Battery: Note the orientation of the old CR2 battery and gently remove it.
- Insert New Battery: Insert a new CR2 battery, ensuring the positive (+) side is facing the correct direction as indicated inside the remote.
- Close the Casing: Carefully snap the remote casing back together, ensuring it is securely closed.
Dispose of old batteries according to local regulations.
6. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Remote not responding / Short range | Low or dead battery. Interference from other electronic devices. Remote is out of range. | Replace the CR2 battery. Move away from sources of interference. Ensure you are within the operational range of the vehicle's system. |
| Remote LED does not light up | Dead battery. Faulty remote. | Replace the CR2 battery. If the issue persists, the remote may need replacement. |
| Remote unpairs from vehicle system | System reset or programming loss. | Re-program the remote to the vehicle's system following the steps in Section 3. |
| Vehicle does not respond to commands | Remote not programmed. Vehicle battery low. System in Valet Mode. | Ensure the remote is correctly programmed. Check vehicle battery. Exit Valet Mode (refer to your main system manual). |
7. Specifications
- Model: Viper 7654V
- Type: SuperCode SST 1-Way Companion Remote
- Brand: Viper
- Item Weight: 1.76 ounces
- Product Dimensions: 8 x 5.9 x 0.5 inches
- Batteries: 1 CR2 battery required
- Voltage: 12 Volts
- Special Features: Ergonomic design
- Compatible Devices: Viper systems 5501, 4702V, 5901, 5702V, 4704, 4704V, 5902, 5902V, 5704, 5704V
8. Warranty and Support
For warranty information and technical support, please refer to the documentation included with your complete Viper security or remote start system. You may also visit the official Viper website or contact their customer service for assistance.
Online Resources: www.viper.com
