Introduction
Thank you for choosing the BONTEC Universal Tabletop TV Stand. This manual provides essential information for the safe and proper assembly, operation, and maintenance of your new TV stand. Please read all instructions carefully before beginning assembly and retain this manual for future reference.
This stand is designed to provide a stable and adjustable base for flat-panel televisions ranging from 26 to 55 inches, with a maximum VESA compatibility of 400x400 mm and a maximum load capacity of 40 kg (88 lbs).
Safety Information
- Do not exceed the maximum load capacity of 40 kg (88 lbs).
- Ensure your TV's VESA pattern is compatible (up to 400x400 mm).
- Always use two people for lifting and mounting the TV.
- Place the stand on a stable, level surface.
- Keep children and pets away during assembly.
- Check all connections and fasteners regularly to ensure they remain secure.
Package Contents
Verify that all components are present and undamaged before assembly. If any parts are missing or damaged, contact customer support.
- Base (Tempered Glass)
- Support Pillar
- TV Mounting Bracket
- TV Mounting Arms (2x)
- Hardware Kit (screws, washers, spacers, anti-slip feet, cable clips)
- Assembly Tools (Allen key, wrench)
Setup and Assembly
Follow these steps carefully for proper assembly. It is recommended to have a second person assist with the assembly, especially when mounting the TV.
Step 1: Attach Anti-Slip Feet to the Base
Carefully place the tempered glass base on a soft, clean surface to prevent scratches. Attach the anti-slip rubber feet to the designated spots on the underside of the glass base.
Step 2: Assemble the Support Pillar to the Base
Secure the support pillar to the tempered glass base using the provided screws and tools. Ensure the pillar is firmly attached and upright.
Step 3: Attach the TV Mounting Bracket to the Pillar
Connect the TV mounting bracket to the top of the support pillar. Make sure it is aligned correctly and tightened securely.
Step 4: Attach TV Mounting Arms to Your TV
Identify the VESA mounting holes on the back of your TV. Select the appropriate screws, washers, and spacers from the hardware kit that fit your TV's VESA pattern. Attach the two TV mounting arms vertically to the back of your TV. Ensure the hooks on the arms face upwards.
Step 5: Mount the TV onto the Stand
With assistance, carefully lift your TV and hook the attached mounting arms onto the TV mounting bracket on the stand. Ensure both arms are securely seated on the bracket. Tighten the safety screws on the bottom of the mounting arms to prevent accidental dislodgement.
Operating Instructions
Height Adjustment
The BONTEC TV stand offers multiple levels of height adjustment for optimal viewing. There are 3 levels of height adjustment for the TV plate and 2 levels for the TV hooks, each adjustable by 5 cm (2 inches).
- To adjust the height of the TV plate: Loosen the screws securing the TV mounting bracket to the pillar. Slide the bracket up or down to the desired height and re-tighten the screws firmly.
- To adjust the height of the TV hooks: The TV mounting arms have multiple holes. Before mounting the TV, select the desired height by attaching the arms to the TV using the appropriate set of holes.
Cable Management
The stand features an integrated cable management system to keep your entertainment area tidy. Use the provided cable clips to route and secure TV and device cables along the back of the support pillar.
Maintenance
- Cleaning: Use a soft, dry cloth to clean the stand. For the glass base, a glass cleaner can be used. Avoid abrasive cleaners or solvents that may damage the finish.
- Inspection: Periodically check all screws and connections to ensure they remain tight and secure. Loose connections can compromise stability.
- Relocation: If moving the stand, always lift it carefully with assistance. Do not drag the stand, especially if a TV is mounted, as this can damage the base or the floor.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Stand is wobbly or unstable. | Screws are loose; stand is on an uneven surface; weight capacity exceeded. | Check and tighten all screws. Move the stand to a level surface. Ensure TV weight is within 40kg limit. |
| TV does not fit the stand. | Incorrect VESA pattern; TV size outside recommended range. | Verify your TV's VESA pattern (max 400x400 mm) and screen size (26-55 inches) against specifications. |
| Missing parts. | Packaging error. | Contact BONTEC customer support with your purchase details. |
Specifications
- Model: ST09
- Compatible TV Sizes: 26 - 55 inches
- Maximum Load Capacity: 40 kg (88 lbs)
- VESA Compatibility: 100x100, 200x100, 200x200, 300x300, 400x300, 400x400 mm
- Height Adjustment: 3 levels for TV plate, 2 levels for TV hooks (5 cm increments)
- Base Material: 8mm Tempered Safety Glass
- Pillar/Bracket Material: Alloy Steel
- Product Dimensions: 42.5 x 26 x 61 cm (approximate, varies with height setting)
- Product Weight: 4.12 kg
Warranty and Support
BONTEC products come with a standard manufacturer's warranty. For specific warranty terms and conditions, please refer to the documentation included with your purchase or visit the official BONTEC website.
If you encounter any issues during assembly or operation, or if you have questions about your product, please contact BONTEC customer support. You can often find contact information on the product packaging or the brand's official website.
For additional resources and product information, you may visit the BONTEC Store on Amazon.