Introduction
This instruction manual provides essential information for the proper installation, operation, and maintenance of your Eagle Eyes BZ115-B001L Headlight. This product is designed to be OE-comparable for factory assembly, ensuring a precise fit and performance. It is SAE/DOT compliant, meeting and exceeding the highest national certification requirements, including ISO 9001:2800 and ISO/TS 16949:2009. Please read this manual thoroughly before installation and use to ensure safety and optimal performance.
Product Overview
Image: Eagle Eyes BZ115-B001L Headlight assembly. This image displays the complete headlight unit, featuring its clear lens and integrated bulb housing, designed for the driver's side of a vehicle. The unit appears robust and ready for installation.
What's in the Box:
- One (1) Driver Side Headlamp Assembly (Model: BZ115-B001L)
This package contains the complete driver side headlight assembly, ready for direct replacement or new installation. No additional components are typically required for basic functionality, though specific vehicle models may require additional wiring or adapters (not included).
Setup and Installation
Installation of automotive headlights can be complex and may require specialized tools and knowledge. It is highly recommended that installation be performed by a qualified automotive technician. Incorrect installation can lead to damage to the product, vehicle, or personal injury.
General Installation Steps (Consult Vehicle Service Manual for Specifics):
- Safety First: Ensure the vehicle is turned off, the parking brake is engaged, and the battery is disconnected before beginning any work. Allow sufficient time for existing bulbs to cool down if recently used.
- Access the Headlight Assembly: Depending on your vehicle model, this may involve removing grille components, bumper sections, or fender liners. Refer to your vehicle's specific service manual for detailed instructions.
- Disconnect Wiring: Carefully disconnect all electrical connectors from the existing headlight assembly. Be gentle to avoid damaging the clips or wires.
- Remove Old Headlight: Unbolt or unclip the old headlight assembly from its mounting points. Carefully remove it from the vehicle.
- Install New Headlight: Position the new Eagle Eyes BZ115-B001L Headlight assembly into the opening. Ensure all mounting tabs and alignment pins are correctly seated. Secure it with the original bolts or clips.
- Connect Wiring: Reconnect all electrical connectors to the new headlight assembly. Ensure connections are secure and properly seated.
- Test Functionality: Before reassembling vehicle components, reconnect the battery and test the headlight's functions (low beam, high beam, turn signal, parking light, etc.) to ensure proper operation.
- Reassemble Vehicle: Once confirmed operational, reassemble any removed vehicle components (grille, bumper, etc.).
- Aiming (Important): After installation, it is crucial to properly aim your headlights to ensure optimal visibility and to avoid blinding oncoming drivers. Consult your vehicle's service manual or a professional for correct aiming procedures.
Operating Instructions
The Eagle Eyes BZ115-B001L Headlight operates in conjunction with your vehicle's existing electrical system and headlight controls. No special operating procedures are required for the headlight unit itself beyond standard vehicle operation.
Basic Operation:
- Turning On/Off: Use your vehicle's standard headlight switch to turn the headlights on or off.
- High Beams/Low Beams: Toggle between high and low beams using your vehicle's designated stalk or switch.
- Indicator Lights: Ensure all indicator lights (turn signals, parking lights) integrated into the assembly function correctly when activated via your vehicle's controls.
Always ensure your headlights are clean and properly aimed for safe driving, especially during nighttime or adverse weather conditions.
Maintenance
Proper maintenance will extend the life and maintain the clarity of your headlight assembly.
Cleaning:
- Regularly clean the exterior lens of the headlight with a soft cloth and mild automotive soap or glass cleaner.
- Avoid abrasive cleaners or harsh chemicals, as these can damage the polycarbonate lens material.
- Rinse thoroughly with clean water and dry with a soft, lint-free cloth to prevent water spots.
Inspection:
- Periodically inspect the headlight assembly for any signs of cracks, moisture intrusion, or damage to the lens or housing.
- Check that all bulbs (if replaceable) are functioning correctly. Replace any burnt-out bulbs promptly according to your vehicle's manual.
- Ensure all mounting points remain secure and free from corrosion.
Troubleshooting
This section addresses common issues you might encounter with your headlight assembly.
| Problem | Possible Cause | Solution |
|---|---|---|
| Headlight not turning on | Blown fuse, faulty bulb, loose electrical connection, wiring issue. | Check vehicle's fuse box and replace any blown fuses. Inspect bulb(s) and replace if burnt out. Verify all electrical connections are secure. Consult a professional if wiring issues are suspected. |
| Headlight is dim or flickering | Weak electrical connection, failing bulb, voltage issue. | Check and secure all electrical connections. Replace the bulb. Have vehicle's electrical system checked by a professional. |
| Moisture inside the headlight lens | Condensation (normal in some conditions), seal compromise, crack in housing. | Small amounts of condensation that dissipate quickly are normal. If excessive or persistent, check for cracks or damage to the housing/seals. Ensure all caps and covers are securely in place. If damage is found, replacement may be necessary. |
| Improper light beam pattern | Incorrect aiming, improper installation. | Perform headlight aiming procedure (refer to vehicle manual or professional). Re-check installation to ensure the assembly is seated correctly. |
For issues not listed here or if troubleshooting steps do not resolve the problem, please contact customer support or a certified automotive technician.
Specifications
| Feature | Detail |
|---|---|
| Brand | Eagle Eye Lights |
| Model Number | BZ115-B001L |
| Item Weight | 11.66 pounds |
| Package Dimensions | 23.5 x 14.79 x 13.12 inches |
| Color | Clear |
| Specific Uses For Product | Head Lights |
| Vehicle Service Type | Car |
| Special Feature | Waterproof |
| Lens Color | Clear |
| Lens Material | Polycarbonate |
| UPC | 889521031324 |
| Assembly Required | No (refers to the headlight unit itself, not vehicle installation) |
| Automotive Fit Type | Vehicle Specific Fit |
| Manufacturer | Eagle Eyes |
| Compliance | SAE/DOT compliant, ISO 9001:2800, ISO/TS 16949:2009 |
Warranty Information
Specific warranty terms and conditions for the Eagle Eyes BZ115-B001L Headlight are provided by the manufacturer, Eagle Eye Lights. Warranty coverage typically includes defects in materials and workmanship under normal use.
To obtain detailed warranty information, please refer to the documentation included with your product packaging or visit the official Eagle Eye Lights website. Keep your proof of purchase (receipt or invoice) as it will be required for any warranty claims.
Customer Support
For technical assistance, troubleshooting beyond this manual, or warranty inquiries, please contact the manufacturer or your point of purchase.
Manufacturer: Eagle Eye Lights
Please refer to the product packaging or the manufacturer's official website for the most current contact information, including phone numbers, email addresses, or online support portals.
When contacting support, please have your product model number (BZ115-B001L) and proof of purchase readily available.
