RadioShack 1500526

Download PDF
Contents

RadioShack Antenna-Mounted High-Gain Signal Amplifier

Model: 1500526

Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your RadioShack Antenna-Mounted High-Gain Signal Amplifier. This device is designed to enhance TV signal strength from an outdoor antenna, providing improved picture quality and reception, especially in areas with weaker signals or when splitting the signal to multiple televisions.

Package Contents

Before beginning installation, please verify that all components are present in the package:

  • User's Manual (this document)
  • Outdoor Amplifier Unit
  • Indoor Amplifier Unit
  • AC Adapter (12 VDC, 200 mA)
  • 75-ohm Terminator
  • U-Bolt with nuts (2) & washers (2) for mast mounting
  • 6-Foot Coaxial Cable with weather boots
  • 6-Foot Coaxial Cable (standard)
Included accessories for the RadioShack High-Gain Signal Amplifier
Figure 1: Package Contents. This image displays the various components included with the amplifier: the outdoor amplifier, indoor amplifier, AC adapter, two coaxial cables, a 75-ohm terminator, and U-bolt mounting hardware.

Setup and Installation

The RadioShack Antenna-Mounted High-Gain Signal Amplifier is designed for outdoor antenna installation to maximize signal reception before any signal loss occurs due to long cable runs or signal splitting.

Installation Steps:

  1. Mount the Outdoor Amplifier: Secure the outdoor amplifier unit to your antenna mast using the provided U-bolt and hardware. Ensure it is positioned close to the antenna to minimize signal loss from the antenna to the amplifier.
  2. Connect Antenna to Outdoor Amplifier: Connect the coaxial cable from your outdoor antenna to the 'INPUT' port on the outdoor amplifier.
  3. Connect Outdoor Amplifier to Indoor Amplifier: Run a coaxial cable from the 'OUTPUT' port of the outdoor amplifier to the 'TO ANTENNA' input on the indoor amplifier unit. Use the 6-foot coaxial cable with weather boots for the outdoor connection if needed.
  4. Connect Indoor Amplifier to TV(s): The indoor amplifier has two coaxial outputs. Connect one or both outputs to your television(s) or other receiving devices using coaxial cables. If only one output is used, connect the provided 75-ohm terminator to the unused output port to prevent signal reflection.
  5. Power the Indoor Amplifier: Connect the AC adapter to the 'POWER' input on the indoor amplifier and plug the adapter into a standard electrical outlet. The indoor amplifier powers the outdoor unit through the coaxial cable.
Installation diagram for the RadioShack High-Gain Signal Amplifier
Figure 2: Installation Diagram. This diagram illustrates the connection process from the antenna to the outdoor amplifier, then to the indoor amplifier, and finally to the televisions and power source.

Important Note: When connecting coaxial cables, hand-tighten only. Overtightening can damage the connectors and lead to signal loss.

Operating Instructions

The indoor amplifier unit features controls to optimize your signal reception.

Indoor amplifier unit with gain and signal booster controls
Figure 3: Indoor Amplifier Controls. This image shows the indoor amplifier unit, highlighting the 'GAIN' adjustment dial and the 'SIGNAL BOOSTER' switch.
  • Gain Adjustment Dial (Min/Max GAIN): This dial allows you to adjust the amplification level. Start with the dial set to 'Min' and gradually increase it towards 'Max' while monitoring your TV's signal strength meter. Adjust until you achieve the best possible picture quality without over-amplification, which can cause signal distortion. The gain control provides up to 10dB of adjustment.
  • Signal Booster Switch (ON/OFF): This switch activates or deactivates an additional signal boost feature. If your signal is very weak, switch it to 'ON' for maximum amplification. If you experience signal distortion or pixelation, try switching it to 'OFF' or reducing the gain.

After making adjustments, perform a channel scan on your television to detect any newly available or improved channels.

Maintenance

The RadioShack Antenna-Mounted High-Gain Signal Amplifier is designed for durability and requires minimal maintenance.

  • Outdoor Unit: Periodically inspect the outdoor amplifier and its connections for any signs of weather damage, corrosion, or loose cables. Ensure all connections remain hand-tight.
  • Indoor Unit: Keep the indoor amplifier in a dry, well-ventilated area. Avoid blocking its ventilation openings.
  • Cleaning: Clean both units with a soft, dry cloth. Do not use liquid cleaners or solvents.

Troubleshooting

If you experience issues with your signal amplifier, refer to the following common problems and solutions:

  • No Signal or Poor Picture Quality:
    • Ensure all coaxial cable connections are secure and hand-tight.
    • Verify the AC adapter is properly connected to the indoor amplifier and a working power outlet.
    • Check the antenna's alignment and condition. An amplifier boosts existing signals; it cannot create a signal where none exists.
    • Adjust the 'GAIN' dial on the indoor amplifier. Too much gain can sometimes over-amplify the signal, leading to distortion. Try reducing the gain.
    • Toggle the 'SIGNAL BOOSTER' switch. In some cases, a very strong signal might benefit from the booster being off.
    • Perform a channel scan on your television after making any adjustments.
  • Interference or Pixelation:
    • This can be a sign of over-amplification. Reduce the 'GAIN' setting.
    • Ensure the 75-ohm terminator is installed on any unused output port of the indoor amplifier.
    • Check for other electronic devices near the amplifier or coaxial cables that might be causing interference.
  • Fewer Channels After Installation:
    • Ensure the amplifier is powered on.
    • Perform a full channel scan on your television.
    • Adjust the 'GAIN' dial. Sometimes, a signal can be over-amplified to the point where the TV tuner cannot process it correctly.

Specifications

Part Number1500526
Power Source12 VDC, 200 mA
Frequency Response54-806 MHz
Noise Figure3.5dB (Typical)
Gain33dB (VHF or UHF)
Gain ControlUp to 10dB
Outputs2 Coaxial Outputs (Indoor Unit)
ManufacturerRadioShack
Item Weight1.5 pounds
Date First AvailableJuly 28, 2016

Warranty and Support

Specific warranty information for this product was not provided in the available documentation. For details regarding warranty coverage, please refer to the product packaging or contact RadioShack customer support directly.

Customer Support:

For technical assistance or further inquiries, please visit the official RadioShack website or contact their customer service department. Contact information can typically be found on the product packaging or their official website.

© 2026 RadioShack. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.