Introduction
The One For All Grundig URC1915 replacement remote control is designed to function exactly like your original Grundig TV remote. It offers immediate usability without complex setup, supporting all standard Grundig TV functions including menu navigation, program guide, HDMI input selection, and Smart Hub access. This manual provides comprehensive instructions for setting up, operating, and maintaining your URC1915 remote control.
Setup
1. Inserting Batteries
The URC1915 remote control requires two AAA batteries (not included).
- Locate the battery compartment cover on the back of the remote control.
- Slide the cover downwards to open the compartment.
- Insert two AAA batteries, ensuring the positive (+) and negative (-) terminals align correctly with the markings inside the compartment.
- Slide the battery compartment cover back into place until it clicks securely.
2. Initial Use (No Setup Required)
The One For All URC1915 remote control is pre-programmed for all Grundig TVs. Once batteries are inserted, it is ready for immediate use with your Grundig television. No additional programming or code entry is necessary.
3. Learning Function (Optional)
While the URC1915 is fully functional out of the box, it also features a learning function, allowing you to copy functions from your original remote control if desired. This can be useful for specific functions not pre-programmed or for adapting the remote to personal preferences.
To use the learning function:
- Place the URC1915 remote and your original Grundig remote on a flat surface, facing each other, about 1-2 inches apart.
- On the URC1915, press and hold the SETUP button (if available, or a combination like SHIFT + LEARN if specified in a physical manual) until the LED blinks twice and then stays lit. (Note: Specific button for learning mode may vary, refer to the physical manual for exact details if this remote has a dedicated learning button).
- Press the button on the URC1915 that you wish to program (e.g., a specific function button). The LED will blink rapidly.
- On your original remote, press and hold the corresponding button you want to copy. The URC1915 LED will blink twice to confirm successful learning.
- Repeat steps 3 and 4 for any other buttons you wish to program.
- To exit learning mode, press the SETUP button again (or wait for the LED to turn off automatically).
Operating the Remote Control
The URC1915 remote control provides full functionality for your Grundig TV. Below is a general overview of common button functions.
Image: Front view of the One For All Grundig URC1915 TV Remote Control. This image displays the full layout of the remote, including the power button, number pad, navigation keys, volume and channel controls, and dedicated function buttons for menu, guide, HDMI, and Smart Hub.
- Power Button (●): Turns the TV on or off.
- Number Pad (0-9): Directly select channels.
- Volume Up/Down (+/-): Adjusts the TV volume.
- Channel Up/Down (P+/P-): Changes the TV channel.
- Mute: Mutes or unmutes the TV sound.
- Navigation Keys (Up, Down, Left, Right, OK): Used to navigate menus and select options.
- Menu: Opens the TV's main menu.
- Guide: Accesses the electronic program guide (EPG).
- HDMI: Cycles through HDMI input sources.
- Smart Hub (or similar Smart TV button): Launches the Smart TV platform or applications.
- Exit: Exits the current menu or application.
- Back/Return: Returns to the previous screen or menu.
Operating Range
The URC1915 remote control operates using infrared (IR) technology. Ensure a clear line of sight between the remote and your TV's IR receiver for optimal performance. The maximum effective range is approximately 10 meters (33 feet).
Maintenance
Battery Replacement
Replace the batteries when the remote's response becomes sluggish or it stops functioning. Always replace both batteries at the same time with new AAA alkaline batteries. Do not mix old and new batteries, or different types of batteries.
Cleaning
To clean the remote control, use a soft, dry cloth. Do not use abrasive cleaners, solvents, or chemical sprays, as these can damage the remote's surface or internal components.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Remote does not work. | Batteries are dead or inserted incorrectly. | Replace batteries with new ones, ensuring correct polarity (+/-). |
| Remote works intermittently. | Low battery power; Obstruction between remote and TV. | Replace batteries. Ensure clear line of sight to TV's IR receiver. |
| Certain buttons do not work. | Button may be stuck or damaged; Learning function issue. | Check for physical obstruction. If using learning function, try re-programming the specific button. |
| Remote does not control TV functions correctly. | Remote is not compatible with your specific Grundig TV model (unlikely for URC1915); Learning function misconfiguration. | Verify TV model compatibility (URC1915 is designed for all Grundig TVs). If learning function was used, try resetting the remote (refer to physical manual for reset procedure) or re-programming. |
Specifications
- Model: URC1915
- Brand: One For All
- Color: Black
- Connectivity Technology: Infrared (IR)
- Compatible Devices: Grundig Televisions
- Max. Supported Devices: 1
- Number of Buttons: 15 (typical, may vary slightly based on specific layout)
- Controller Type: Button Control
- Maximum Range: 10 meters (33 feet)
- Power Source: 2 x AAA Batteries (not included)
- Special Features: Pre-programmed for Grundig TVs, Learning Function
- Country of Origin: China
Image: One For All Grundig URC1915 TV Remote Control in its retail packaging. The packaging highlights key features such as "Replacement Remote for Grundig TVs" and "100% Grundig TV Compatible."
Warranty and Support
For detailed warranty information, product support, frequently asked questions, and video tutorials, please visit the official One For All website. Customer service is available to assist with any setup or operational queries.
Note: The user manual is typically included in the product packaging.
