Introduction
This manual provides comprehensive instructions for the Serta Motion Perfect II and III Adjustable Bed Replacement Remote. This genuine OEM replacement remote is designed to work seamlessly with Serta Motion Perfect II or III adjustable bed bases. It is essential to verify your bed base's serial number (located on the crossbar between the legs near the foot of the bed) starts with "33031" to ensure compatibility. This guide covers setup, operation, maintenance, and troubleshooting to help you maximize the functionality of your adjustable bed system.
Safety Information
- Keep the remote control away from liquids and excessive moisture.
- Do not attempt to disassemble or repair the remote control yourself. Refer to qualified service personnel.
- Ensure batteries are inserted with correct polarity to prevent damage.
- Keep batteries out of reach of children. If swallowed, seek immediate medical attention.
- Avoid dropping the remote control to prevent internal damage.
Product Overview
The Serta Motion Perfect II and III Replacement Remote features an intuitive button layout for easy control of your adjustable bed. Familiarize yourself with the buttons and their functions as described below.
Figure 1: Front view of the Serta Motion Perfect II and III Replacement Remote.
Remote Control Buttons:
| Button/Section | Function |
|---|---|
| MASSAGE (10 MIN, 20 MIN, 30 MIN) | Activates the massage function for the specified duration. |
| TIMER/ALL OFF | Turns off all active functions, including massage and bed adjustments. |
| HEAD + / - | Adjusts the head section of the bed up (+) or down (-). |
| FOOT + / - | Adjusts the foot section of the bed up (+) or down (-). |
| ZERO G | Moves the bed to the "Zero Gravity" preset position, which elevates the head and foot slightly to relieve pressure. |
| FLAT | Returns the bed to a completely flat position. |
| HEAD Up/Down Arrows | Fine-tunes the head section adjustment. |
| FOOT Up/Down Arrows | Fine-tunes the foot section adjustment. |
| WAVE Massage (3 buttons) | Activates different wave massage patterns. |
Figure 2: Angled view of the Serta Motion Perfect II and III Replacement Remote.
Setup: Remote Syncing Instructions
Programming is required to sync your new replacement remote with your Serta Motion Perfect II or III adjustable bed base. Follow these steps carefully:
- Locate the Control Box: The control box is typically found under the bed, often attached to the crossbar between the legs near the foot of the bed. It is usually a black or grey box.
- Identify the Pairing Button: On the control box, locate a small button, often labeled "PAIR," "LEARN," or "SYNC." It might be recessed and require a pen or paperclip to press.
- Initiate Pairing Mode: Press and hold the pairing button on the control box for approximately 3-5 seconds. The indicator light on the control box should start blinking, indicating it is in pairing mode.
- Pair the Remote: While the control box light is blinking, immediately press and hold any button on your new replacement remote control (e.g., the "FLAT" button or "HEAD +" button) for 3-5 seconds.
- Confirm Pairing: The indicator light on the control box should stop blinking and become solid, or turn off, indicating successful pairing. Release the button on the remote.
- Test the Remote: Test all functions of the remote control to ensure it is properly synced and operating your adjustable bed.
Note: If the remote does not sync on the first attempt, repeat the steps. Ensure you are within close proximity to the bed base during the syncing process.
Operating Instructions
Once your remote is synced, you can operate your adjustable bed using the following functions:
- Adjusting Head/Foot: Use the HEAD + / - and FOOT + / - buttons to raise or lower the respective sections of the bed. For finer adjustments, use the dedicated Head and Foot arrow buttons.
- Zero Gravity Position: Press the ZERO G button to move the bed to the pre-programmed Zero Gravity position, designed for optimal comfort and pressure relief.
- Flat Position: Press the FLAT button to return the bed to a completely flat sleeping surface.
- Massage Function: Press the MASSAGE buttons (10 MIN, 20 MIN, 30 MIN) to activate the massage feature for the desired duration. Use the wave massage buttons for different patterns.
- Turn All Off: Press the TIMER/ALL OFF button to stop all active functions and return the bed to a neutral state (does not flatten the bed unless it was already flat).
Maintenance
Battery Replacement:
The remote control requires 3 AAA batteries. When the remote's performance diminishes or it stops responding, it's time to replace the batteries.
- Locate the battery compartment cover on the back of the remote control.
- Slide or unclip the cover to open the compartment.
- Remove the old AAA batteries.
- Insert three new AAA batteries, ensuring the correct polarity (+ and -) as indicated inside the compartment.
- Replace the battery compartment cover securely.
- Dispose of old batteries according to local regulations.
Note: If the remote does not function after battery replacement, try re-syncing it with the bed base as described in the "Setup" section.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Remote not responding to bed. | Batteries are dead or incorrectly inserted. Remote is not synced. Power outage to bed base. | Replace batteries, ensuring correct polarity. Re-sync the remote following the "Setup" instructions. Check if the bed base is plugged into a working power outlet. |
| Bed only moves in one direction or partially. | Obstruction under the bed. Motor issue. | Check for any objects obstructing the bed's movement. If the issue persists, contact customer support. |
| Massage function not working. | Massage motor issue. | Ensure the bed is powered. If still not working, contact customer support. |
| Remote light blinks but bed doesn't move. | Remote is out of range or not properly synced. | Move closer to the bed base. Re-sync the remote. |
Specifications
- Product Dimensions: 2 x 1 x 6 inches
- Item Weight: 4.8 ounces
- Model Number: OK-50107
- Batteries: 3 AAA batteries required
- Color: Silver
- Manufacturer: Ergomotion
- Compatible Devices: Serta Motion Perfect II and III Adjustable Bed Bases (serial # starting with 33031)
Warranty and Support
For warranty information or technical support regarding your Serta Motion Perfect II and III Adjustable Bed Replacement Remote, please contact the seller or manufacturer directly. Refer to your purchase documentation for specific warranty terms and contact details. For general inquiries or assistance with syncing, please reach out to the retailer from whom you purchased the remote.
