Introduction
Thank you for choosing the Melnor AquaTimer 1-Zone Automatic Water Timer. This digital timer is designed to simplify your watering routine, allowing you to set precise schedules for your lawn and plants. Please read this manual carefully to ensure proper setup, operation, and maintenance of your device.
Product Overview
An image of the Melnor AquaTimer 1-Zone Automatic Water Timer, highlighting its key features. The timer is dark gray with a large, easy-to-read LCD screen displaying 'AM 7:00'. A yellow control dial with 'MANUAL ON/OFF', arrow buttons, and a '+' and '-' button is visible on the right. The main dial on the left has positions for 'OFF', 'SET CLOCK', 'START WATER', 'HOW LONG', 'HOW OFTEN', and 'AUTO'. Callouts point to the filter washer at the top connection, the large LCD screen, the easy-touch buttons for scheduling, and the high flow valve at the bottom outlet.
- Filter Washer: Ensures clean water flow and protects the timer mechanism.
- Large LCD Screen: Provides clear display of time and programming settings.
- Control Dial: Used to navigate through different programming modes.
- Easy-Touch Buttons: For setting time, duration, and frequency.
- High Flow Valve: Designed for efficient water delivery.
Setup
1. Battery Installation
- Remove the battery compartment cover on the back of the timer.
- Insert two (2) fresh AA alkaline batteries, ensuring correct polarity (+/-).
- Replace the battery compartment cover securely.
2. Attaching to Faucet
- Ensure the filter washer is properly seated in the timer's inlet connection.
- Thread the timer onto a standard outdoor spigot. Hand-tighten only to prevent damage.
- Open the spigot fully to allow water flow to the timer. The timer will control the water flow.
3. Connecting Hoses
- Attach your garden hose to the outlet at the bottom of the timer. Hand-tighten securely.
Operating Instructions
1. Setting the Current Time (SET CLOCK)
- Turn the dial to SET CLOCK.
- Use the +/- buttons to adjust the hour. Press the arrow button to switch between hours and minutes.
- Press the arrow button again to confirm and move to setting AM/PM.
- Use the +/- buttons to select AM or PM.
- Turn the dial to AUTO to save the time.
2. Programming a Watering Schedule
The timer allows you to set a specific start time, duration, and frequency for watering.
a. Set Start Time (START WATER)
- Turn the dial to START WATER.
- Use the +/- buttons to adjust the desired watering start hour. Press the arrow button to switch to minutes.
- Use the +/- buttons to adjust the minutes. Press the arrow button to switch to AM/PM.
- Use the +/- buttons to select AM or PM.
b. Set Watering Duration (HOW LONG)
- Turn the dial to HOW LONG.
- Use the +/- buttons to set the watering duration from 1 minute up to 6 hours.
c. Set Watering Frequency (HOW OFTEN)
- Turn the dial to HOW OFTEN.
- Use the +/- buttons to select the watering frequency (e.g., every 6 hours, every 12 hours, every day, every 2 days, etc.).
3. Manual Watering (MANUAL ON/OFF)
To water manually without interrupting your programmed schedule:
- Press the MANUAL ON/OFF button.
- Use the +/- buttons to set the desired manual watering duration.
- Press MANUAL ON/OFF again to start watering.
- To stop manual watering, press MANUAL ON/OFF again. The timer will return to its programmed schedule.
4. Rain Delay
To pause your watering schedule due to rain or other reasons:
- While the dial is in AUTO mode, press and hold the +/- button for 3 seconds.
- Use the +/- buttons to select the desired delay duration (up to 7 days).
- The timer will automatically resume its schedule after the delay period.
5. Activating Programmed Schedule (AUTO)
- After setting all desired parameters, turn the dial to AUTO. The timer will now operate according to your programmed schedule.
6. Turning Off the Timer (OFF)
- To completely stop all watering, turn the dial to OFF.
Maintenance
1. Filter Washer
- Periodically inspect the filter washer located at the timer's inlet.
- If debris is present, remove the timer from the faucet, take out the washer, and rinse it thoroughly under running water.
- Reinsert the clean filter washer before reattaching the timer.
2. Battery Replacement
- Replace batteries annually or when the low battery indicator appears on the LCD screen.
- Always use fresh alkaline batteries for optimal performance.
3. Winterization
- Before the first freeze, disconnect the timer from the faucet and remove the batteries.
- Store the timer indoors in a dry, protected area to prevent damage from freezing temperatures.
Troubleshooting
- Timer Not Watering:
- Ensure the faucet is fully open.
- Check battery level and replace if low.
- Verify that the dial is set to AUTO and a schedule is programmed.
- Inspect the filter washer for clogs.
- Leaking from Connections:
- Ensure all connections (faucet to timer, timer to hose) are hand-tight.
- Check that the filter washer is correctly seated.
- If necessary, use plumbing tape on the threads for a tighter seal.
- Incorrect Time or Schedule Not Holding:
- Re-set the current time using the SET CLOCK function.
- Verify all programmed watering settings (start time, duration, frequency).
- Ensure the dial is returned to AUTO after programming.
Specifications
| Model Number | 63015 |
| Brand | Melnor |
| Number of Zones | 1 |
| Material | Metal |
| Product Dimensions | 1"D x 1"W x 1"H |
| Item Weight | 6.4 Ounces |
| Screen Size | 5.1 Inches |
| UPC | 042206630155 |
Warranty
Melnor products typically come with a limited warranty. For specific warranty details, duration, and registration information, please refer to the official Melnor website or the product packaging. Keep your purchase receipt as proof of purchase.
Support
For technical assistance, replacement parts, or further product information, please visit the official Melnor website at www.melnor.com or contact Melnor customer service directly. Contact details can usually be found on the website or product packaging.