Evotech Performance Ducati Monster Fender Eliminator / Tail Tidy Instruction Manual

Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of the Evotech Performance Fender Eliminator / Tail Tidy for Ducati Monster 1200-S-797 models from 2017 and 2018. This product is designed to replace the bulky factory fender, offering a cleaner, more streamlined appearance to the rear of your motorcycle while maintaining functionality for license plate mounting and turn signals.

Safety Information

Always prioritize safety when working on your motorcycle. Read all instructions thoroughly before beginning installation. If you are unsure about any step, consult a qualified motorcycle mechanic. Use appropriate tools and wear personal protective equipment, including eye protection and gloves.

• Ensure the motorcycle is stable and securely supported before starting any work.
• Disconnect the battery if working with electrical components.
• Do not overtighten fasteners; refer to your motorcycle's service manual for torque specifications if available.
• Keep small parts away from children.

Package Contents

Please verify that all components are present before beginning installation. If any parts are missing or damaged, contact Evotech Performance customer support.

• Fender Eliminator Bracket
• License Plate Mount
• LED License Plate Light (if included with specific kit)
• Mounting Hardware (bolts, washers, nuts)
• Cable Ties (for wire management)
• Installation Instructions (this manual)

Setup and Installation

This section outlines the general steps for installing the fender eliminator. Specific details may vary slightly depending on your motorcycle's exact configuration. Refer to your Ducati Monster service manual for detailed instructions on removing factory components.

Tools Required:

• Socket Wrench Set
• Hex Key Set (Allen wrenches)
• Wire Strippers/Crimpers (if wiring is required)
• Zip Tie Cutters
• Torque Wrench (recommended)

Installation Steps:

1. Prepare the Motorcycle: Park the motorcycle on a level surface and secure it on a stand. Ensure the engine is cool.
2. Remove Rear Seat and Tail Section: Carefully remove the rear seat and any fairings or covers necessary to access the factory fender assembly and wiring.
3. Disconnect Electrical Connections: Disconnect the wiring for the factory license plate light and turn signals. Note their routing for reinstallation.
4. Remove Factory Fender: Unbolt and remove the entire factory fender assembly. Keep all factory hardware in case you need to revert to stock.

Figure 1: Original factory fender assembly before removal.
5. Install Evotech Fender Eliminator Bracket: Mount the new Evotech Performance fender eliminator bracket to the motorcycle's subframe using the provided hardware. Ensure it is securely fastened.
6. Mount License Plate and Lights: Attach your license plate to the new bracket. If your kit includes an LED license plate light, install it and connect its wiring.
7. Connect Turn Signals: If reusing factory turn signals or installing aftermarket ones, connect them to the appropriate wiring. Ensure proper polarity for LED lights.


Figure 2: Side view of the motorcycle with the Evotech Performance Fender Eliminator installed.

8. Route and Secure Wiring: Neatly route all wiring to prevent pinching or chafing. Use cable ties to secure wires away from moving parts and heat sources.
9. Test Functionality: Before reassembling the tail section, test the license plate light and turn signals to ensure they are working correctly.
10. Reassemble Tail Section: Reinstall any removed fairings, covers, and the rear seat. Ensure all fasteners are tightened to factory specifications.


Figure 3: Rear view of the motorcycle with the Evotech Performance Fender Eliminator fully installed.

11. Final Inspection: Double-check all connections and fasteners. Ensure nothing is loose and that the license plate is securely mounted and visible.

Operating Considerations

Once installed, the Evotech Performance Fender Eliminator operates passively as a mounting solution. Ensure your license plate and any integrated lighting (license plate light, turn signals) are fully functional and comply with local regulations. Periodically check all mounting bolts for tightness, especially after the first few rides, as vibrations can sometimes cause fasteners to loosen.

Maintenance

The Evotech Performance Fender Eliminator is constructed from durable materials designed for longevity with minimal maintenance.

• Cleaning: Clean the fender eliminator with mild soap and water. Avoid abrasive cleaners or harsh chemicals that could damage the finish.
• Inspection: Regularly inspect the bracket and all mounting hardware for any signs of wear, damage, or corrosion.
• Fastener Check: Periodically check all bolts and nuts for proper tightness. Re-torque if necessary, referring to your motorcycle's service manual for appropriate torque values.

Troubleshooting

If you encounter issues after installation, consider the following common problems and solutions:

Specifications

Warranty and Support

Evotech Performance products are manufactured to high standards. For specific warranty information or technical support, please refer to the official Evotech Performance website or contact their customer service directly. Keep your proof of purchase for warranty claims.

Contact Information:

• Website: www.evotech-performance.com
• Email: Refer to website for contact details.