1. Introduction
Thank you for choosing the Sammic Smartvide 7 Immersion Circulator. This manual provides essential information for the safe and efficient operation, maintenance, and troubleshooting of your new sous vide cooker. Please read all instructions carefully before using the appliance and retain this manual for future reference.
2. Safety Instructions
To ensure safe operation, always follow these basic safety precautions:
- Electrical Safety: Ensure the appliance is connected to a grounded outlet with the correct voltage. Do not operate with a damaged cord or plug. Keep the power cord away from hot surfaces.
- Water and Heat: This appliance operates in hot water. Exercise extreme caution to prevent burns. Do not immerse the main unit (above the minimum water level mark) in water.
- Children and Pets: Keep the appliance out of reach of children and pets.
- Stable Surface: Always place the water bath on a stable, heat-resistant surface.
- Ventilation: Ensure adequate ventilation around the appliance during operation.
- Maintenance: Unplug the appliance before cleaning or performing any maintenance.
3. Package Contents
Verify that all items are present in the package:
- Sammic Smartvide 7 Immersion Circulator
- Instruction Manual (this document)
4. Setup
Follow these steps to set up your Smartvide 7 Immersion Circulator:
- Choose a Container: Select a heat-resistant container (pot, tank, or tub) with a capacity of up to 56 liters (14 gallons).
- Secure the Circulator: Attach the Smartvide 7 to the side of your chosen container using the integrated clamp. Ensure it is securely fastened and stable.
- Fill with Water: Fill the container with water, ensuring the water level is between the minimum and maximum fill lines indicated on the circulator.
- Connect Power: Plug the power cord into a grounded electrical outlet. The display will illuminate.

Image showing the Sammic Smartvide 7 Immersion Circulator, ready for installation into a water bath.
5. Operating Instructions
5.1 Basic Operation
The Smartvide 7 features a touch control interface for easy operation.
- Power On: After plugging in, the unit will be in standby mode. Press the power button to turn it on.
- Display: The display will show the current water temperature and the set target temperature.
5.2 Setting Temperature
To set your desired cooking temperature:
- Press the 'Set Temp' button.
- Use the '+' and '-' buttons to adjust the temperature to your desired setting. The temperature can be set up to 212°F (100°C).
- Press 'Set Temp' again or wait a few seconds for the setting to be confirmed. The circulator will begin heating the water to the target temperature.
5.3 Using the Timer
The integrated timer allows for precise cooking durations:
- Once the water reaches the target temperature, press the 'Timer' button.
- Use the '+' and '-' buttons to set the desired cooking time in hours and minutes.
- Press 'Timer' again or wait a few seconds to start the countdown.
- An alarm will sound when the timer expires. Press any button to silence it.
6. Maintenance
6.1 Cleaning
Regular cleaning ensures optimal performance and longevity:
- Before Cleaning: Always unplug the appliance and allow it to cool completely.
- Exterior: Wipe the exterior with a damp cloth. Do not use abrasive cleaners or immerse the control head in water.
- Heating Coil/Pump: For mineral buildup, fill a container with a mixture of water and white vinegar (e.g., 1:1 ratio). Clamp the circulator into the container, ensuring the heating coil is submerged. Run the circulator at 140°F (60°C) for 20-30 minutes. Rinse thoroughly with clean water.
6.2 Storage
Store the Smartvide 7 in a clean, dry place when not in use. Ensure it is completely dry before storing.
7. Troubleshooting
Refer to the table below for common issues and their solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Unit does not power on | Not plugged in; power outlet issue; damaged cord | Check power connection; try a different outlet; inspect cord for damage (do not use if damaged) |
| Water not heating | Low water level; heating element malfunction | Ensure water is above minimum fill line; contact customer support if issue persists |
| Temperature fluctuates | Container too large for water volume; lid not used | Use an appropriately sized container; cover the water bath to minimize heat loss |
| Error code displayed | Specific internal issue | Refer to the specific error code in a more detailed technical manual or contact customer support |
8. Specifications
Technical specifications for the Sammic Smartvide 7 Immersion Circulator:
| Feature | Specification |
|---|---|
| Model Number | 1180022 |
| Brand | Sammic |
| Capacity | Up to 14 Gallons (56 Liters) |
| Material | Stainless Steel |
| Control Method | Touch |
| Upper Temperature Rating | 212 Degrees Fahrenheit (100 Degrees Celsius) |
9. Warranty and Support
For warranty information, please refer to the warranty card included with your product or visit the official Sammic website. For technical support or service inquiries, please contact Sammic customer service through their official channels. Keep your purchase receipt as proof of purchase for warranty claims.





