Weiser SmartCode 10 Keyless Entry Deadbolt Lock User Manual

Introduction

This manual provides comprehensive instructions for the installation, operation, programming, and maintenance of your Weiser SmartCode 10 Keyless Entry Deadbolt Lock. Please read this manual thoroughly before installation and use to ensure proper function and security.

Figure 1: Exterior view of the Weiser SmartCode 10 Keyless Entry Deadbolt Lock in Polished Brass finish, showing the keypad and keyhole.

Package Contents

Verify that all components are present before beginning installation:

• Exterior Keypad Assembly
• Interior Assembly Unit
• Latch
• Strike Plate
• Mounting Plate
• Adapter Ring
• 2 Keys
• Screws
• SmartKey Tool
• 4 AA Batteries
• Installation Guide (this manual)

Setup and Installation

Before installation, ensure your door meets the following specifications:

• Door thickness: 1-3/8" to 2" (35mm - 51mm)
• Cross bore hole diameter: 2-1/8" (54mm)
• Backset: 2-3/8" or 2-3/4" (60mm or 70mm)

Tools Required:

• Phillips Head Screwdriver
• Measuring Tape
• Pencil

Installation Steps:

1. Prepare the Door: If replacing an existing lock, remove it. Ensure the door frame is properly prepared for the strike plate.
2. Install Latch: Insert the latch into the door edge. Ensure the "UP" arrow on the latch is facing upwards. Secure with screws.
3. Install Exterior Assembly: Route the cable from the exterior keypad assembly through the cross bore hole. Position the exterior assembly flush against the door.
4. Install Mounting Plate: Secure the mounting plate to the door using the provided screws, ensuring the cable passes through the plate.
5. Connect Cables: Connect the cable from the exterior assembly to the interior assembly.
6. Install Interior Assembly: Attach the interior assembly to the mounting plate. Ensure the turn piece shaft engages correctly with the latch mechanism. Secure with screws.
7. Install Batteries: Insert the 4 AA batteries into the battery pack of the interior assembly.
8. Perform Door Handing Process: This step is crucial for the lock to learn the orientation of your door.
   • With the door open and unlocked, press the "Lock" button on the keypad.
   • The latch bolt should extend and retract. If it does not, repeat the process.

Figure 2: The Weiser SmartCode 10 deadbolt lock installed on a dark wooden door, showcasing its integration with existing door hardware.

Operating Instructions

Programming User Codes:

The lock supports up to 16 user codes and one master code. The master code is used to add or delete user codes and should be kept confidential.

1. Set Master Code (First Time Only):
   • Open the battery cover on the interior assembly.
   • Press the "Program" button once.
   • Enter a new 4-8 digit master code on the keypad.
   • Press the "Lock" button.
   • Re-enter the master code.
   • Press the "Lock" button. A successful programming will be indicated by a green flash and a beep.
2. Add User Code:
   • Open the battery cover.
   • Press the "Program" button once.
   • Enter the master code.
   • Press the "Lock" button.
   • Enter a new 4-8 digit user code.
   • Press the "Lock" button. A successful programming will be indicated by a green flash and a beep.
3. Delete User Code:
   • Open the battery cover.
   • Press the "Program" button twice.
   • Enter the master code.
   • Press the "Lock" button.
   • Enter the user code to be deleted.
   • Press the "Lock" button. A successful deletion will be indicated by a green flash and a beep.

Locking the Door:

• From Exterior: Press the "Lock" button on the keypad. The deadbolt will extend.
• From Interior: Rotate the turn piece to the vertical position.

Unlocking the Door:

• Using Keypad: Enter a valid user code or master code. The deadbolt will retract.
• Using Key: Insert the key into the keyhole and turn.
• From Interior: Rotate the turn piece to the horizontal position.

Figure 3: Interior view of the Weiser SmartCode 10 deadbolt lock, showing the battery compartment and turn piece.

SmartKey Re-keying Instructions

The SmartKey feature allows you to re-key your lock to a new key in seconds. This is useful if you want to match your lock to an existing key or if you lose a key.

1. Insert your functioning key fully into the cylinder.
2. Rotate the key 90 degrees clockwise.
3. Insert the SmartKey tool firmly into the SmartKey hole.
4. Remove the SmartKey tool.
5. Remove your functioning key.
6. Insert your new key fully into the cylinder.
7. Rotate the new key 90 degrees counter-clockwise.
8. Rotate the new key 90 degrees clockwise again to ensure it functions correctly.

Figure 4: Diagram illustrating the SmartKey Security features, including resistance to kick-ins, bumps, picks, drills, and saws.

Maintenance

• Battery Replacement: When the batteries are low, the lock will emit a series of beeps and the keypad will flash red after locking/unlocking. Replace all four AA batteries promptly.
• Cleaning: Clean the keypad and exterior finish with a soft, damp cloth. Avoid abrasive cleaners or solvents, which can damage the finish.
• Lubrication: Periodically lubricate the latch bolt and deadbolt mechanism with a silicone-based lubricant to ensure smooth operation. Do not lubricate the key cylinder.

Troubleshooting

Specifications

• Model: 9GED17000-001
• Finish: Polished Brass
• Material: Brass
• Door Thickness: 1-3/8" to 2" (35mm - 51mm)
• Cross Bore: 2-1/8" (54mm)
• Backset: Adjustable 2-3/8" or 2-3/4" (60mm or 70mm)
• User Codes: Up to 16 (4-8 digits)
• Power Source: 4 AA Alkaline Batteries (included)
• Special Features: Keyless Entry, Backlit Keypad, One-Touch Locking, SmartKey Re-key Technology, Auto-Lock
• Product Dimensions: 9.4 x 13.72 x 25.4 cm
• Item Weight: 1.69 kg

Warranty and Support

This Weiser SmartCode 10 Keyless Entry Deadbolt Lock comes with a Limited Lifetime Warranty. For detailed warranty information or technical support, please refer to the official Weiser website or contact customer service.

Manufacturer: Weiser

Website: www.weiserlock.com (Example link, actual link may vary)

Customer Service: Refer to the Weiser website for contact information specific to your region.