Introduction
This manual provides instructions for the installation and operation of the EASYGUARD P2 Replacement Push Start Stop Button. This button is designed as a replacement part and is only compatible with specific EASYGUARD car alarm systems.
Compatibility: This replacement button is exclusively compatible with EASYGUARD EC002 series PKE car alarms, EC110 series, ES002 series, and ES003 series systems. It is not designed for use with other car alarm systems or as a standalone product.
Product Overview
The EASYGUARD P2 Push Start Stop Button features a dynamic LED illumination that changes color based on the vehicle's status:
- When the system is disarmed, or the ACC/ON ignition is active, the button illuminates in blue.
- Once the engine is started, the button illumination changes to red.
Image: The EASYGUARD P2 Push Start Stop Button illustrating its blue illumination when disarmed or in ACC/ON mode, and red illumination when the engine is running. Key dimensions are also shown: 28mm, 41mm, and 52mm.
Image: Components included with the EASYGUARD P2 Push Start Stop Button: the button itself, a mounting bracket, and the necessary wiring harness for connection.
Setup and Installation
This replacement button is intended for integration with existing EASYGUARD EC002, EC110, ES002, or ES003 series systems. Professional installation is recommended to ensure correct wiring and functionality.
Pre-Installation Checks:
- Verify that your existing car alarm system is one of the compatible EASYGUARD series (EC002, EC110, ES002, ES003).
- Ensure the vehicle's battery is disconnected before beginning any electrical work.
- Identify the location for the new push start button. Ensure sufficient space behind the mounting surface for the button and its wiring.
Installation Steps:
- Remove Existing Button (if applicable): Carefully disconnect and remove the old push start button from its mounting location.
- Prepare Mounting Location: If installing in a new location, drill a hole of appropriate diameter (refer to product dimensions for exact size, approximately 41mm for the main body) for the button.
- Connect Wiring: Connect the wiring harness of the P2 button to the corresponding wires of your EASYGUARD car alarm system. Refer to your specific EASYGUARD system's wiring diagram for accurate connections. Pay close attention to power, ground, ignition, and start signal wires.
- Mount the Button: Insert the P2 button into the prepared opening. Secure it using the provided mounting bracket and hardware. Ensure the button is firmly seated and does not wobble.
- Secure Wiring: Route and secure all wiring to prevent interference with moving parts or accidental disconnection.
- Reconnect Battery: Once all connections are secure and verified, reconnect the vehicle's battery.
Note: Incorrect wiring can damage the product or vehicle's electrical system. If you are unsure about any step, consult a qualified automotive technician.
Operating Instructions
The EASYGUARD P2 Push Start Stop Button functions in conjunction with your compatible EASYGUARD car alarm system. Its operation is typically as follows:
- Disarm System / ACC / ON: When your EASYGUARD system is disarmed, or the ignition is set to ACC or ON, the P2 button will illuminate in blue.
- Starting the Engine: With the system disarmed and the brake pedal pressed, press the P2 button once to start the engine. Upon successful engine start, the button's illumination will change to red.
- Stopping the Engine: To stop the engine, press the P2 button once while the vehicle is stationary. The button's illumination will revert to blue (or off, depending on the system's disarmed state).
- ACC/ON Mode without Starting: Depending on your EASYGUARD system, a quick press of the button without pressing the brake may cycle through ACC and ON modes. Refer to your main EASYGUARD system manual for specific details on this functionality.
Important: Always ensure the vehicle is in park (P) or neutral (N) and the parking brake is engaged before starting or stopping the engine.
Maintenance
The EASYGUARD P2 Push Start Stop Button requires minimal maintenance. Follow these guidelines to ensure its longevity:
- Cleaning: Wipe the button surface with a soft, dry, or slightly damp cloth. Avoid using abrasive cleaners, solvents, or harsh chemicals, as these can damage the finish or internal components.
- Inspection: Periodically check the button for any signs of physical damage, loose connections, or unusual operation.
- Environmental Conditions: While designed for automotive use, avoid exposing the button to extreme temperatures or excessive moisture beyond normal vehicle operating conditions.
Troubleshooting
If you encounter issues with your EASYGUARD P2 Push Start Stop Button, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Button does not illuminate. |
|
|
| Button illuminates but engine does not start. |
|
|
| Button color does not change. |
|
|
For further assistance, contact EASYGUARD customer support or a certified installer.
Specifications
| Feature | Detail |
|---|---|
| Model Number | P2 |
| Brand | EASYGUARD |
| Compatibility | EASYGUARD EC002, EC110, ES002, ES003 series car alarm systems |
| Operation Mode | Push, Push Start, Start Stop |
| Contact Type | Normally Open |
| Connector Type | Micro USB (internal connection, not external user port) |
| Circuit Type | 1-way |
| Mounting Type | Panel Mount |
| Actuator Type | Push Button |
| Contact Material | Metal |
| International Protection Rating | IP00 |
| Number of Positions | 2 |
| Control Method | Touch |
| Connectivity Protocol | X-10 (likely refers to the main system's protocol) |
| Illumination Color | Blue (Disarm/ACC/ON), Red (Engine Started) |
| Unit Count | 1 |
| Item Dimensions (L x W x H) | 7.87 x 3.15 x 1.18 inches (packaging dimensions) |
| Item Weight | 1.34 ounces |
| Voltage | 12 Volts |
| Manufacturer | Zhongshan easyguard electronics co.,ltd |
Warranty and Support
Specific warranty details for the EASYGUARD P2 Replacement Push Start Stop Button are typically provided with the original EASYGUARD car alarm system or can be obtained directly from EASYGUARD customer service.
For technical support, installation inquiries, or warranty claims, please contact EASYGUARD through their official channels. Refer to the documentation included with your main EASYGUARD system for contact information or visit the official EASYGUARD website.
Manufacturer: Zhongshan easyguard electronics co.,ltd
