1. Introduction
This manual provides essential instructions for the safe assembly, operation, and maintenance of your Intex 28241EH Metal Frame Above Ground Swimming Pool Set. Please read all instructions carefully before installation and use. Retain this manual for future reference.
2. Safety Information
WARNING: Failure to follow these instructions can result in serious injury or death.
- Adult Supervision Required: Never leave children unattended in or near the pool.
- Prevent Drowning: Install fencing or approved barriers around the pool. Ensure all gates and doors are secured.
- No Diving or Jumping: The pool is not deep enough for diving or jumping. Serious injury can result.
- Electrical Safety: Connect the filter pump only to a grounded outlet protected by a Ground Fault Circuit Interrupter (GFCI). Do not use extension cords.
- Chemical Handling: Follow all chemical manufacturer's instructions for safe handling, storage, and disposal.
- Emergency Preparedness: Keep a telephone and emergency numbers near the pool. Learn CPR.
- Ladder Safety: Always face the ladder when entering or exiting the pool. Do not allow more than one person on the ladder at a time. Remove the ladder when the pool is not in use to prevent unsupervised access.
3. Package Contents
Verify that all components listed below are present before beginning assembly:
- Pool Liner (1)
- Metal Frame Components (Legs, Horizontal Beams, T-Joints)
- Krystal Clear Cartridge Filter Pump (1000 GPH) (1)
- Removable Pool Ladder (1)
- Pool Cover (1)
- Ground Cloth (1)
- Repair Patch (1)
- Hoses and Clamps for Filter Pump Connection
Image: Overview of the Intex 28241EH Metal Frame Pool Set components.
4. Setup Instructions
Follow these steps for proper pool assembly. It is recommended to have at least two adults for assembly.
4.1 Site Preparation
- Select a firm, level area for the pool. The ground must be completely flat to prevent structural stress and potential collapse.
- Clear the area of any sharp objects, debris, or vegetation.
- Spread the included ground cloth over the prepared area. This provides additional protection for the pool liner.
4.2 Frame Assembly
The innovative T-Joint design allows for quick assembly without tools.
- Lay out the pool liner on top of the ground cloth, ensuring the drain plug is positioned correctly for future draining.
- Assemble the horizontal beams and vertical legs according to the diagrams provided in the separate assembly guide. Insert the T-Joints to connect the frame pieces.
- Ensure all frame pieces are securely connected and the frame forms a perfect circle.
Image: Visual guide for pool setup steps.
4.3 Filling the Pool
- Begin filling the pool with a few inches of water.
- Smooth out any wrinkles in the bottom of the liner by pushing them towards the outer edge.
- Continue filling the pool to the recommended water level, typically just below the filter pump intake/outlet connections.
4.4 Filter Pump and Ladder Installation
- Connect the Krystal Clear Cartridge Filter Pump to the pool's intake and outlet fittings using the provided hoses and clamps. Ensure all connections are tight to prevent leaks.
- Assemble the removable ladder according to its specific instructions. Place the ladder securely on a level surface outside the pool.
5. Operating Instructions
5.1 Krystal Clear Cartridge Filter Pump
The included 1000 GPH (Gallons Per Hour) filter pump features HydroAeration Technology for improved water quality.
- Initial Operation: After filling the pool and connecting the pump, ensure the pump is primed (refer to pump manual for specific priming instructions). Plug the pump into a GFCI-protected electrical outlet.
- Run Time: Operate the filter pump daily for a minimum of 4-6 hours to ensure adequate water circulation and filtration. Adjust run time based on pool usage and water conditions.
- HydroAeration Technology: This system injects air into the water, accelerating circulation, joining fine particles into larger clusters for better filtration, improving water clarity, and increasing negative ions for freshness.
Image: Intex Krystal Clear C1000 Cartridge Filter Pump.
5.2 Water Treatment
Maintaining proper water chemistry is crucial for a safe and clean swimming environment. Consult a pool supply professional for specific chemical recommendations and testing kits.
- Regularly test pH, chlorine, and alkalinity levels.
- Add appropriate chemicals as needed to maintain balanced water.
- Shock the pool periodically to eliminate contaminants.
6. Maintenance
6.1 Filter Cartridge Cleaning and Replacement
The filter cartridge should be cleaned regularly and replaced every 2-4 weeks, depending on pool usage and water quality.
- Disconnect the filter pump from the power source.
- Close the plunger valves on the pool's intake and outlet fittings to prevent water flow.
- Open the filter pump housing and remove the cartridge.
- Rinse the cartridge thoroughly with a garden hose. If heavily soiled or damaged, replace it with a new Intex Type A filter cartridge.
- Reassemble the pump and open the plunger valves before restarting.
6.2 Pool Cover Usage
Use the included pool cover when the pool is not in use to keep out debris and reduce water evaporation.
Image: Intex Metal Frame Pool with the debris cover in place.
6.3 General Cleaning
- Skim the surface of the water daily to remove leaves and other floating debris.
- Brush the pool walls and bottom regularly to prevent algae growth.
- Vacuum the pool floor as needed.
6.4 Winterization
Before freezing temperatures, the pool must be completely drained, cleaned, and disassembled for storage. Refer to the separate winterization guide for detailed instructions.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Pump not running | No power; GFCI tripped; Motor issue | Check power connection; Reset GFCI; Contact customer support |
| Poor water circulation | Clogged filter cartridge; Air in system; Low water level | Clean/replace filter; Bleed air from pump; Add water to pool |
| Water cloudy/green | Insufficient filtration; Imbalanced chemicals; Algae growth | Increase pump run time; Test and adjust chemicals; Shock pool |
| Water leaking from connections | Loose clamps; Damaged O-rings/gaskets | Tighten clamps; Inspect and replace O-rings/gaskets |
8. Specifications
- Brand: Intex
- Model Number: 28241EH
- Product Dimensions: 180"L x 180"W x 48"H (15 ft diameter x 48 in height)
- Shape: Round
- Material: Plastic, Polyvinyl Chloride (PVC) - 3-Ply Puncture-Resistant
- Water Capacity: 4,440 Gallons (16,805 Liters)
- Water Depth: 42 inches (1.07 meters)
- Item Weight: 148.5 Pounds
- Filter Pump: Krystal Clear Cartridge Filter Pump, 1000 GPH (3,785 L/hr)
- Assembly Required: Yes
- Special Feature: Weather Resistant
Image: Pool dimensions and water capacity.
9. Warranty and Support
For warranty information, technical assistance, or to order replacement parts, please contact Intex customer support. Refer to the contact information provided in your product packaging or visit the official Intex website.
UPC: 078257282418
