ResMed AirFit/AirTouch N20 Headgear User Manual

1. Introduction

This manual provides essential information for the proper use, care, and maintenance of your ResMed AirFit/AirTouch N20 Headgear. This headgear is designed as a replacement component for compatible ResMed CPAP mask systems.

Important Note: This product includes only the headgear. The complete mask system, including the frame and nasal cushion, is sold separately and may require a prescription.

This image displays the ResMed AirFit/AirTouch N20 Headgear, a replacement component for CPAP masks. It features a light grey fabric with purple accents, designed for comfort and secure fit.

An exploded diagram illustrating the various components of the AirFit/AirTouch N20 mask system, including the headgear, frame, cushion, and short tube. This helps visualize how the headgear integrates with the complete mask.

2. Setup and Fitting

The ResMed AirFit/AirTouch N20 Headgear is designed for easy integration with your existing compatible mask frame and cushion. Follow these general steps for setup and fitting:

1. Attach Headgear: Connect the headgear straps to the designated attachment points on your AirFit N20 or AirTouch N20 mask frame. Ensure all connections are secure.
2. Position Mask: Hold the mask cushion against your face and pull the headgear over your head.
3. Adjust Straps: Adjust the upper and lower headgear straps evenly to achieve a comfortable and secure fit. The headgear should feel snug but not overly tight, allowing for proper seal without discomfort.
4. Check Size: Verify that you are using the correct headgear size for optimal fit and performance.

A woman demonstrating the proper wear of the ResMed AirFit/AirTouch N20 CPAP mask, showing how the headgear secures the nasal cushion and frame comfortably around the head.

Close-up of hands holding the headgear, highlighting the 'N20' and 'S' (Small) size indicator printed on the strap, emphasizing the importance of checking the correct headgear size.

3. Operating and Comfort

Once properly fitted, the AirFit/AirTouch N20 Headgear provides stability and comfort for your CPAP therapy. The soft, flexible material is designed to minimize pressure points and enhance your sleep experience.

Ensure the headgear allows for a secure seal of the nasal cushion without causing excessive pressure on your face. If you experience discomfort or air leaks, readjust the straps as needed.

An image showing a couple sleeping comfortably while wearing ResMed AirFit N20 and AirTouch N20 masks, illustrating the product's intended use and comfort.

4. Maintenance and Cleaning

Regular cleaning of your headgear is crucial for hygiene and to maintain its performance. Follow these guidelines for proper care:

• Wash Weekly: The headgear should be washed weekly.
• Disassemble: Disassemble the headgear from the mask frame before cleaning. Magnets, if present, can remain attached.
• Soak: Soak the headgear in warm water with a mild liquid detergent for approximately 10 minutes.
• Rinse: Rinse thoroughly under warm, running drinking-quality water.
• Squeeze: Gently squeeze to remove excess water.
• Air Dry: Air dry the headgear out of direct sunlight.

A visual checklist detailing the recommended cleaning procedure for the AirFit/AirTouch N20 headgear, including washing frequency, disassembly, soaking, rinsing, squeezing, and air drying.

Replacement Recommendations

We recommend replacing your headgear every 6 months to ensure optimal performance and hygiene. Consider replacing your headgear if you observe any of the following signs:

• You frequently need to tighten the straps to maintain a seal.
• The material has stretched out and no longer provides a secure fit.
• The headgear is discolored from hair oils or other products.
• Your sleep therapy feels less effective than usual, potentially due to an improper mask seal.

This image provides guidance on when to replace the headgear, recommending replacement every 6 months and listing signs such as frequent strap tightening, stretched material, discoloration, and reduced therapy effectiveness.

5. Troubleshooting

If you encounter issues with your headgear, consider the following:

• Poor Seal/Leaks: Ensure the headgear is correctly positioned and adjusted. Over-tightening can also cause leaks by distorting the cushion. Check for signs of wear or stretching as indicated in the replacement recommendations.
• Discomfort: Readjust the straps to relieve pressure points. Ensure the headgear is not twisted. If discomfort persists, verify you have the correct size headgear.
• Headgear Slipping: This may indicate the headgear is stretched or worn out and requires replacement. Ensure hair is not caught under the straps.

For persistent issues, consult your healthcare provider or contact ResMed customer support.

6. Specifications

7. Warranty Information

For specific warranty details regarding your ResMed AirFit/AirTouch N20 Headgear, please refer to the documentation provided with your original purchase or contact ResMed directly. Warranty terms typically cover manufacturing defects for a specified period.

8. Support

If you require further assistance, have questions about your product, or need to report an issue, please contact ResMed customer support. You can find contact information on the official ResMed website or through your product supplier.

Visit the ResMed Store for more information and products.