Hifonics ZEX1950.1D

Download PDF
Contents

Hifonics Zeuz ELITE ZEX1950.1D Car Audio Amplifier Instruction Manual

Model: ZEX1950.1D

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your Hifonics Zeuz ELITE ZEX1950.1D Mono Block Class D Subwoofer Amplifier. This amplifier is designed to deliver high-quality audio performance for your car's subwoofer system. Please read this manual thoroughly before installation and use to ensure proper function and safety.

Hifonics Zeuz ELITE ZEX1950.1D Mono Block Amplifier

Figure 1: Hifonics Zeuz ELITE ZEX1950.1D Mono Block Amplifier. This image shows the top view of the black amplifier with the Hifonics logo and "ZEUS ELITE 1900 Watts" text clearly visible. The model number ZEX1950.1D is also printed on the side.

2. Key Features

  • Power Output: 1900 Watts RMS at 1 Ohm, 950 Watts RMS at 2 Ohms, 525 Watts RMS at 4 Ohms.
  • Class D Design: Efficient Class D mono subwoofer amplifier.
  • Simpatico Coil Design (SPC): Enhances performance.
  • Ultra-Fi Pulse Width Modulated MOSFET Power Supply: Ensures stable and efficient power delivery.
  • LED Indicators: Blue LED for power, Red LED for protection status.
  • Remote Bass Level Control: Wired remote included for convenient bass adjustment.
  • Variable Bass Boost: 0 to +12 dB bass boost at 45 Hz.
  • Blue Illuminated Hifonics Badge: Aesthetic feature.
  • Soft Start Sound Function: Prevents turn-on thumps.
  • Preamp RCA Outputs: Allows daisy-chaining multiple amplifiers.
  • 4-Way System Protection: Thermal, overload, DC offset, and speaker short protection.
  • Dual 12 Gauge Speaker Terminals: Simplifies speaker wire connections.
  • Heavy Duty Aluminum Alloy Vented Heatsink: Maximizes heat dissipation.
  • Silver Nickel-Plated RCA Inputs and Screw Terminals: Ensures optimal signal transfer and secure connections.
  • Variable Low-Pass Filter: 30-250 Hz, 24 dB/octave.
  • Subsonic Filter: 15-35 Hz.
  • Frequency Response: 15-250 Hz.

3. Setup and Installation

Proper installation is crucial for optimal performance and safety. It is recommended that installation be performed by a qualified professional. Always disconnect the vehicle's battery before beginning any electrical work.

3.1. Mounting the Amplifier

Choose a mounting location that is dry, well-ventilated, and away from direct sunlight or heat sources. Ensure sufficient space around the amplifier for proper airflow. Secure the amplifier firmly to a solid surface using appropriate hardware.

Hifonics ZEX1950.1D Amplifier Side View

Figure 2: Side view of the Hifonics ZEX1950.1D amplifier, showing the input and output terminals. This view highlights the robust construction and terminal layout for wiring connections.

3.2. Wiring Connections

Follow these steps for wiring:

  1. Power Connection: Connect a heavy-gauge power cable (minimum 4 AWG recommended for 1900W RMS) directly from the vehicle's positive battery terminal to the amplifier's +12V terminal. Install an appropriate fuse (e.g., 150A) within 18 inches of the battery.
  2. Ground Connection: Connect a heavy-gauge ground cable (same gauge as power cable) from the amplifier's GND terminal to a clean, unpainted metal surface on the vehicle chassis. Ensure a solid, low-resistance connection.
  3. Remote Turn-On: Connect a remote turn-on wire from your head unit's remote output to the amplifier's REM terminal. This wire signals the amplifier to turn on and off with the head unit.
  4. RCA Input: Connect RCA cables from your head unit's subwoofer pre-out to the amplifier's RCA input jacks.
  5. Speaker Output: Connect your subwoofer(s) to the amplifier's speaker terminals. The ZEX1950.1D is 1 Ohm stable, allowing for flexible subwoofer configurations. Ensure correct polarity (+ to + and - to -). Use dual 12 gauge speaker terminals for simplified hookup.
Hifonics ZEX1950.1D Amplifier Terminal View

Figure 3: Close-up view of the Hifonics ZEX1950.1D amplifier's control panel and terminals. This image details the various input, output, and adjustment controls on the amplifier.

4. Operating Instructions

Once installed, adjust the amplifier settings for optimal audio performance.

4.1. Initial Power-Up

After all connections are made, reconnect the vehicle's battery. Turn on your head unit. The blue power LED on the amplifier should illuminate, indicating it is receiving power and is operational.

4.2. Gain Adjustment

Set the amplifier's gain control to match the output voltage of your head unit. Start with the gain at minimum, play a familiar track at about 75% of your head unit's maximum volume, and slowly increase the amplifier's gain until you hear distortion, then back off slightly. This ensures maximum clean signal without clipping.

4.3. Crossover Settings

  • Low-Pass Filter (LPF): Adjust the variable low-pass filter (30-250 Hz) to allow only low frequencies to pass to the subwoofer. A common starting point is 80-100 Hz, but this may vary depending on your subwoofer and other speakers.
  • Subsonic Filter: Adjust the subsonic filter (15-35 Hz) to remove extremely low frequencies that your subwoofer cannot reproduce efficiently. This protects the subwoofer from damage and improves sound quality.

4.4. Bass Boost

The amplifier features a variable bass boost (0 to +12 dB at 45 Hz). Use this control sparingly to enhance bass response. Excessive bass boost can lead to distortion and potential damage to your subwoofer.

4.5. Remote Bass Level Control

The included wired remote bass level control allows for convenient adjustment of the subwoofer output from the driver's seat. Connect the remote to the designated port on the amplifier.

Hifonics Remote Bass Level Control

Figure 4: Hifonics wired remote bass level control. This compact unit features a blue illuminated knob for adjusting bass output conveniently.

5. Maintenance

The Hifonics ZEX1950.1D amplifier requires minimal maintenance to ensure long-term performance.

  • Cleaning: Periodically wipe the amplifier's exterior with a soft, dry cloth to remove dust. Do not use harsh chemicals or abrasive cleaners.
  • Ventilation: Ensure that the heatsink fins are free from obstructions to allow for proper heat dissipation.
  • Connections: Periodically check all wiring connections (power, ground, remote, RCA, speaker) to ensure they are secure and free from corrosion. Loose connections can lead to poor performance or damage.

6. Troubleshooting

If you experience issues with your amplifier, refer to the following troubleshooting guide. The amplifier features 4-Way System Protection circuitry (thermal, overload, DC, and speaker short protection) which may activate and illuminate the red protect LED.

ProblemPossible CauseSolution
No Power (Power LED Off)
  • Blown fuse at battery or amplifier.
  • Loose or disconnected power/ground wire.
  • No remote turn-on signal.
  • Check and replace fuses.
  • Verify all power, ground, and remote connections are secure.
  • Check head unit's remote output.
Amplifier in Protection Mode (Protect LED On)
  • Overheating (thermal protection).
  • Speaker short circuit.
  • Low impedance load (below 1 Ohm).
  • DC offset detected.
  • Allow amplifier to cool down; ensure proper ventilation.
  • Check speaker wiring for shorts.
  • Verify subwoofer impedance matches amplifier capability.
  • Check RCA inputs and head unit for DC voltage.
No Sound Output
  • Loose RCA cables.
  • Incorrect gain setting.
  • Speaker wires disconnected.
  • Head unit settings incorrect.
  • Check RCA connections at both amplifier and head unit.
  • Adjust gain control.
  • Verify speaker connections.
  • Ensure head unit's subwoofer output is enabled and volume is up.
Distorted Sound
  • Gain set too high.
  • Bass boost set too high.
  • Incorrect crossover settings.
  • Damaged speaker.
  • Reduce gain.
  • Reduce bass boost.
  • Adjust LPF and Subsonic filter settings.
  • Inspect subwoofer for damage.

7. Specifications

FeatureSpecification
Model NumberZEX1950.1D
RMS Power Rating (4 Ohms)525 Watts x 1 channel
RMS Power Rating (2 Ohms)950 Watts x 1 channel
RMS Power Rating (1 Ohm)1900 Watts x 1 channel
Amplifier ClassClass D
Number of Channels1 (Mono)
Input Sensitivity (Variable Level)200mV - 6V
Variable Low-Pass Filter30-250 Hz, 24 dB/octave
Subsonic Filter15-35 Hz
Bass Boost0 to +12 dB at 45 Hz
Frequency Response15-250 Hz
Damping Factor>200
Dimensions (L x W x H)39.9 x 25.4 x 6.1 Centimeters
Material TypeAluminium
Item Weight10 Pounds
Voltage6 Volts
Specification MetCE, FCC

8. Warranty and Support

For warranty information and technical support, please refer to the documentation provided with your purchase or contact Hifonics customer service directly. Warranty terms and conditions may vary by region and retailer.

Manufacturer: Hifonics

Model: ZEX1950.1D

UPC: 806576223733

© 2023 Hifonics. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.