Bunn Titan Single Brewer Instruction Manual

Introduction

This manual provides detailed instructions for the safe and efficient operation, installation, and maintenance of your Bunn Titan Single Brewer, Model TITAN-SNGL-0000. Please read this manual thoroughly before operating the appliance to ensure proper use and to prevent potential hazards.

Important Safety Information

Always follow basic safety precautions when using electrical appliances to reduce the risk of fire, electric shock, and injury to persons. Retain these instructions for future reference.

• Read all instructions before operating the brewer.
• Do not touch hot surfaces. Use handles or knobs.
• To protect against fire, electric shock, and personal injury, do not immerse cord, plugs, or the appliance in water or other liquid.
• Close supervision is necessary when any appliance is used by or near children.
• Unplug from outlet when not in use and before cleaning. Allow to cool before putting on or taking off parts, and before cleaning the appliance.
• Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions, or has been damaged in any manner. Return appliance to the nearest authorized service facility for examination, repair, or adjustment.
• The use of accessory attachments not recommended by the appliance manufacturer may result in fire, electric shock, or personal injury.
• Do not use outdoors.
• Do not let cord hang over edge of table or counter, or touch hot surfaces.
• Do not place on or near a hot gas or electric burner, or in a heated oven.
• Always attach plug to appliance first, then plug cord into the wall outlet. To disconnect, turn any control to "off", then remove plug from wall outlet.
• Do not use appliance for other than intended use.

Setup Instructions

Before initial use, ensure the brewer is placed on a stable, level surface and connected to a suitable power supply and water source according to local codes and regulations.

1. Unpacking: Carefully remove the brewer from its packaging. Inspect for any shipping damage. Report any damage to the carrier immediately.
2. Placement: Position the brewer in a well-ventilated area, away from heat sources and direct sunlight. Ensure adequate clearance around the unit for air circulation and maintenance access.
3. Water Connection: Connect the brewer to a potable cold water supply using appropriate plumbing fittings. Ensure all connections are secure and leak-free. A water filter is recommended for optimal performance and longevity.
4. Electrical Connection: Plug the brewer into a grounded electrical outlet that matches the voltage and amperage requirements specified on the product label. Do not use extension cords.
5. Initial Fill: Open the water supply valve. The internal tank will begin to fill. Allow the tank to fill completely before proceeding.
6. Heating: Turn on the brewer's power switch. The water in the tank will begin to heat to the optimal brewing temperature. This process may take several minutes.
7. Flushing Cycle: Once heated, run several cycles of hot water through the brewer without coffee to flush out any manufacturing residues and sanitize the system.

Operating the Brewer

This section outlines the steps for brewing coffee with your Bunn Titan Single Brewer.

1. Prepare Filter: Place a clean, commercial-grade paper filter into the brew funnel. Ensure the filter is properly seated.
2. Add Coffee: Measure the appropriate amount of ground coffee for your desired brew strength and volume. Distribute the coffee evenly in the filter. Refer to your coffee supplier's recommendations for optimal ratios.
3. Insert Funnel: Slide the brew funnel securely into the funnel rails beneath the spray head. Ensure it clicks into place.
4. Place Server: Position an empty, clean coffee server (e.g., airpot or decanter) directly beneath the brew funnel. Ensure it is correctly aligned to catch all brewed coffee.
5. Initiate Brew: Press the "Brew" button or activate the brew cycle according to your model's specific controls. The brewer will dispense hot water over the coffee grounds.
6. Monitor Brewing: Allow the brewing cycle to complete. The brewer features pre-infusion and pulse brew technology for optimal extraction, which may result in pauses during the cycle.
7. Serve: Once brewing is complete, carefully remove the server and serve the freshly brewed coffee. Exercise caution as the server and coffee will be hot.
8. Discard Grounds: Remove the brew funnel, discard the used coffee grounds and filter, and clean the funnel thoroughly after each use.

Maintenance and Cleaning

Regular cleaning and maintenance are crucial for the longevity, optimal performance, and hygiene of your Bunn Titan Single Brewer.

• Daily Cleaning:
  • Clean the brew funnel and spray head after each use to prevent coffee residue buildup.
  • Wipe down the exterior of the brewer with a damp cloth and mild detergent. Avoid abrasive cleaners.
  • Empty and clean the drip tray (if applicable) to prevent overflow and maintain cleanliness.
• Weekly Cleaning:
  • Remove and thoroughly clean the spray head to prevent mineral buildup and ensure even water distribution.
  • Inspect and clean the water inlet screen for any debris that might restrict water flow.
• Descaling (as needed):
  • Mineral deposits can accumulate over time, affecting brewer performance and coffee taste. Follow manufacturer guidelines for descaling procedures, typically involving a commercial descaling solution.
  • Caution: Always unplug the brewer and allow it to cool completely before descaling. Rinse thoroughly after descaling to remove all solution.
• General Care:
  • Do not use abrasive cleaners, steel wool, or scouring pads, as these can damage the stainless steel finish and internal components.
  • Ensure all parts are dry before reassembling and operating the brewer.

Troubleshooting

This section addresses common issues you might encounter with your Bunn Titan Single Brewer and provides potential solutions.

Product Specifications

• Model: TITAN-SNGL-0000
• Brand: Bunn
• Brewing Capacity: 22.5 gallons per hour
• Features: Coffee extraction controlled with pre-infusion & pulse brew, digital temperature control, large spray head, BrewMETER™, SplashGard™ funnel
• Funnel Capacity: 28 ounces
• Operation Mode: Fully Automatic
• Color: Stainless
• ASIN: B071YPGDNX
• Manufacturer: Bunn

Warranty and Customer Support

For detailed warranty information and technical support, please refer to the documentation provided with your original purchase or visit the official Bunn website. It is recommended to keep your purchase receipt as proof of purchase for any warranty claims.

Manufacturer: Bunn

Website: www.bunn.com