Hqdz Diamond Selector II
Contents
User Manual for Hqdz Diamond Tester Pen
Model: Diamond Selector II
Brand: Hqdz
Introduction
The Hqdz Diamond Selector II is a professional, high-accuracy jewelry diamond tester pen designed for quick, precise, and safe diamond testing. It is suitable for both novices and experts in jewelry appraisal. This manual provides essential information on setting up, operating, maintaining, and troubleshooting your device to ensure optimal performance.
Setup
1. Battery Installation
The Diamond Tester requires one standard 9V battery for operation, which is included in the package. Ensure the battery is inserted correctly into the designated compartment, observing polarity.
2. Initial Power-On and Calibration
Upon powering on the device, a beeping sound signifies the need for initialization settings. Refer to the table located on the rear of the device for specific initialization settings based on the diamond's temperature and size. Adjust the initial number of illuminated lights by rotating the knob. The default setting is typically four lights illuminated at room temperature.
Figure 1: The Hqdz Diamond Selector II, demonstrating its use with a ring and a loose diamond. The device features an LCD display and LED indicators for readings.
Operating Instructions
1. Preparation for Testing
- Ensure the device is powered on and properly calibrated according to the setup instructions.
- All tests must be performed with bare hands. Wearing gloves will prevent the metal alert from functioning, as a normal moisture level from your hands is necessary for proper operation.
- When holding the diamond tester, your right index finger must continuously touch the electricity conductive panel on the back of the unit.
- For accurate results, all tests must be done using two hands: one hand to hold the diamond or jewelry piece, and the other to operate the diamond tester. Testing with only one hand may lead to inaccurate results.
2. Performing a Test
Gently place the tip of the Diamond Tester on the gemstone. Light pressure is sufficient. The device uses thermal conductivity to differentiate between diamonds and other materials.
Figure 2: Testing a diamond set in a ring. Ensure the probe touches only the stone, not the metal setting.
Figure 3: Testing a loose diamond on the provided testing platform for accurate readings.
3. Interpreting Results
- The device features an LCD display and LED indicators. It emits audible sounds to easily differentiate readings.
- If the stone is a genuine diamond, the tester will typically indicate this with a specific light pattern (e.g., hitting red on the indicator) and an audible signal.
- If the stone is fake, crystal, or cubic zirconia, the tester will not beep or will show a different light pattern.
Note on Videos: No official product videos from the seller were available for embedding in this manual. The available videos were created by influencers and are not included as per instructions.
Maintenance
1. Cleaning the Probe
Regularly clean the test pen probe to maintain its cleanliness, which enhances testing efficacy and accuracy.
2. Battery Care
- The battery temperature can significantly affect the device's use time, especially if it falls below 10 degrees Celsius.
- Always turn off the power after testing to conserve battery life.
3. Storage
Store the Diamond Tester in its leather pouch case when not in use to protect the probe and the device from damage.
Troubleshooting
- Beeping Upon Startup: This indicates the need for initialization settings. Ensure correct battery installation and adequate power. Clean the test pen probe if necessary. Consult the table on the rear of the machine for specific initialization settings based on diamond temperature and size.
- High-Frequency Sound when Testing Metal: This is normal. The test pen relies on thermal conductivity. Since metal possesses thermal conductivity similar to diamonds, it generates a high-frequency sound during testing. Ensure the probe only touches the gemstone, not the metal setting.
- Inaccurate Results:
- Ensure you are performing tests with bare hands and that your right index finger is touching the conductive panel on the back of the tester.
- Always use two hands for testing: one to hold the diamond/jewelry, and one to operate the tester.
- Verify that the operating temperature is within the range of 10-35 degrees Celsius and humidity is below 80%.
- Perform measurements in no-wind conditions for best accuracy.
Specifications
| Feature | Detail |
|---|---|
| Product Dimensions | 3.94 x 1.57 x 1.18 inches |
| Item Weight | 5.28 ounces |
| Batteries | 1 A batteries required (included) |
| Power Source | Battery Powered |
| Color | Black |
| Manufacturer | Hqdz |
| First Available | April 5, 2017 |
Warranty and Support
Information regarding product warranty and specific support contacts is not available in the provided product data. Please refer to the product packaging or the manufacturer's official website for detailed warranty terms and customer support options.
Ask a question about this manual
Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.