Introduction
The DLHONORV Jet Flame Pencil 503 Torch Lighter is a versatile and refillable butane torch designed for various indoor and outdoor applications. It features an adjustable flame, allowing users to switch between a powerful jet flame and a regular flame, and to control the flame height for different tasks. This manual provides essential information for safe and effective operation, maintenance, and troubleshooting.
Safety Information
- WARNING: Keep out of reach of children.
- Contains flammable butane gas. Do not puncture or incinerate.
- Do not expose to heat above 49°C (120°F).
- Do not keep lit for more than 8 minutes continuously to prevent overheating.
- Ensure the switch is OFF when refilling.
- Use only in well-ventilated areas.
- Avoid direct contact with skin or clothing when lit.
- Always point the torch away from yourself and others when igniting.
Setup
Refilling Butane Gas
The torch lighter is shipped without butane gas due to transport safety regulations. It must be filled before first use.
- Ensure the 'Switch' button is in the OFF position.
- Hold the lighter upside down. Firmly press the nozzle of a standard butane gas canister vertically into the refill inlet at the bottom of the lighter.
- Press down for approximately 5-10 seconds. Repeat 2-3 times until the lighter is full. Do not overfill.
- After refilling, allow the lighter to stand for 1-2 minutes before ignition to allow the butane to stabilize and any incomplete volatilization to dissipate.
Detailed text description for Figure 1: This image displays the bottom section of the DLHONORV 503 Torch Lighter, highlighting the 'Inflation Hole' labeled 'GAS'. The diagram indicates where to insert the butane canister nozzle for refilling. A note below the image advises allowing the lighter to stand for 1-2 minutes after the first inflation before use to ensure proper ignition.
Operating Instructions
Ignition
- Turn the 'Switch' (on/off button) to the ON side.
- Press the 'Igniter Ball' at the bottom of the lighter to ignite the flame.
Detailed text description for Figure 2: This image shows a three-panel guide on how to use the torch lighter. Panel 1 instructs to 'Turn the Red Rolling Wheel Dial to the jet flame.' Panel 2 instructs to 'Turn the Switch to the "ON" side.' Panel 3 instructs to 'Press the Igniter Ball at the bottom to ignite,' showing a hand holding the lighter with a blue jet flame active.
Flame Adjustment
- Adjusting Flame Height: Slide the 'Flame Regulator' to increase (+) or decrease (-) the flame height as needed.
- Switching Flame Type: Rotate the 'Red Rolling Wheel Dial' to switch between a powerful jet flame and a regular soft flame.
Detailed text description for Figure 3: This image highlights the 'Two Flame Modes' of the DLHONORV 503 Torch Lighter. It shows the lighter in use, producing a blue jet flame. An inset circle illustrates the lighter producing a yellow soft flame. The image points to the 'Red Rolling Wheel Dial' as the control for switching between these two flame types.
Turning Off
- Release the 'Igniter Ball'.
- Turn the 'Switch' to the OFF position to ensure the gas flow is completely stopped.
Operational Demonstration
Detailed text description for Video 1: This video demonstrates the operation of the DLHONORV 503 Torch Lighter. It shows a hand holding the lighter, activating the jet flame, then adjusting it to a soft flame, and finally turning it off. The video highlights the ease of switching between flame types and adjusting flame intensity.
Detailed text description for Video 2: This video provides a detailed look at the DLHONORV 503 Torch Lighter. It illustrates how to operate the switch, adjust the flame, and refill the butane. The video also shows the lighter in action, demonstrating both the jet flame and soft flame capabilities.
Maintenance
- Keep the lighter clean and free from dust or debris, especially around the nozzle and ignition mechanism.
- Use a soft, dry cloth for cleaning. Do not use abrasive cleaners or solvents.
- Store in a cool, dry place away from direct sunlight and heat sources.
- Ensure the lighter is completely off and cooled before storing.
Troubleshooting
- Lighter does not ignite after refilling: Allow 1-2 minutes for butane to stabilize. Ensure the 'Switch' is ON. Check if the igniter ball is fully pressed.
- Flame is weak or inconsistent: Refill with butane. Adjust the 'Flame Regulator' for a higher flame. Ensure the nozzle is clean and free of obstructions.
- Gas leaks: Ensure the refill valve is properly sealed after refilling. If leaks persist, discontinue use and contact customer support.
Specifications
| Feature | Detail |
|---|---|
| Model Number | 503 |
| Dimensions (L x W x H) | 16.5 x 2.5 x 2 cm |
| Weight | 90 g |
| Material | Metal and ABS |
| Continuous Burn Time | Max 8 minutes |
| Maximum Temperature | 1300°C |
| Fuel Capacity | 5.38 ml |
| UPC | 748440935949 |
| Manufacturer | QIANGUANG |
Warranty Information
For warranty information, please refer to the product packaging or contact the retailer where the product was purchased. Keep your proof of purchase for any warranty claims.
Customer Support
For technical assistance, troubleshooting, or further inquiries regarding your DLHONORV Jet Flame Pencil 503 Torch Lighter, please contact DLHONORV customer support through your retailer or the official brand website. Please have your model number (503) and any relevant purchase details ready.