USARemote Car Key Fob Keyless Entry Remote with Ignition Key (OUC60270, OUC60221) Instruction Manual

1. Introduction

This manual provides detailed instructions for the USARemote Car Key Fob Keyless Entry Remote with Ignition Key. This product is designed as a replacement for lost or damaged key fobs and includes a complete electronic assembly with a battery. It offers keyless entry functionality and an ignition key for starting your vehicle.

The remote is user-programmable for vehicles manufactured before 2010. For vehicles from 2010 and newer, programming must be performed by a qualified locksmith or dealership. The ignition key is user-programmable, provided you have at least one existing working key.

2. Compatibility

This key fob and ignition key set is compatible with the following vehicle models and part numbers:

• Replacement for Part Numbers: OUC60270, OUC60221, 1585784, 15913427, 20869057, 22756462

Compatible Vehicle Models:

• Cadillac:
  • 2007-2014 Escalade (includes ESV and EXT)
• Chevrolet:
  • 2007-2014 Suburban (includes 1500 and 2500)
  • 2007-2014 Tahoe
  • 2009-2017 Traverse
• GMC:
  • 2007-2014 Yukon (includes 1500 and 2500)

3. What's Included

Each package contains:

• Complete key fob with electronics and a pre-installed battery.
• Uncut transponder chip ignition key.

4. Setup and Programming

4.1. Ignition Key Cutting

The included ignition key is uncut and must be professionally cut to match your vehicle's existing key. This service can typically be performed by a locksmith or a hardware store that offers key cutting services. Ensure the service provider can cut transponder keys.

4.2. Ignition Key Programming (User Programmable)

If you have at least one existing, working ignition key, you can program the new cut key yourself. Follow these steps:

1. Insert your existing, working key into the ignition and turn it to the 'ON' position (do not start the engine).
2. Wait for the security indicator light on the dashboard to turn off.
3. Within 20 seconds, remove the existing key.
4. Immediately insert the newly cut key into the ignition and turn it to the 'ON' position.
5. Wait for the security indicator light to turn off. The new key is now programmed.
6. Test the new key to ensure it starts the vehicle.

4.3. Remote Fob Programming

For vehicles manufactured before 2010: The remote fob is user-programmable. Detailed step-by-step instructions are typically provided with the product packaging. Please refer to those specific instructions for your vehicle model.

For vehicles manufactured in 2010 and newer: The remote fob must be programmed by a professional locksmith or a dealership. These vehicles often require specialized diagnostic equipment for programming.

Note: If programming multiple remotes, all remotes (existing and new) must be programmed at the same time. Failure to do so may result in older remotes no longer functioning.

5. Operating Instructions

The key fob features standard buttons for vehicle control:

• Lock Button: Press once to lock all vehicle doors.
• Unlock Button: Press once to unlock the driver's door, press twice to unlock all doors.
• Remote Start Button: Press and hold to remotely start the vehicle (if equipped). Refer to your vehicle's owner's manual for specific remote start procedures.
• Trunk/Liftgate Release Button: Press twice to open the trunk or liftgate (if equipped).
• Panic Button: Press and hold to activate the vehicle's alarm system. Press again to deactivate.

6. Maintenance

6.1. Battery Replacement

The key fob uses one CR2 battery. When the remote's range decreases or it stops responding, the battery may need replacement. To replace the battery:

1. Carefully open the key fob casing.
2. Remove the old CR2 battery.
3. Insert a new CR2 battery, ensuring correct polarity.
4. Close the key fob casing securely.

Note: Refer to your vehicle's owner's manual or the specific instructions provided with the key fob for detailed battery replacement steps, as procedures may vary slightly.

7. Troubleshooting

• Remote not working after programming: Ensure all remotes were programmed simultaneously. If not, repeat the programming process for all remotes. For 2010+ vehicles, confirm professional programming was completed correctly.
• Ignition key not starting vehicle: Verify the key was cut correctly by a professional. Ensure the key programming steps (Section 4.2) were followed precisely. If issues persist, consult a locksmith.
• Remote start not functioning: For GM vehicles, the remote start feature may be limited to two uses before requiring a manual key start to reset the system. Perform a manual key start, then re-attempt remote start.
• Reduced remote range: Replace the key fob battery (see Section 6.1).
• Buttons are too sensitive: This is a characteristic of the design. Exercise care to avoid accidental button presses when carrying the fob.

8. Specifications

9. Warranty and Support

This product is an aftermarket replacement part. For specific warranty information, please refer to the documentation provided with your purchase or contact USARemote customer service.

USARemote offers technical support to assist with any questions regarding installation, programming, or functionality. Please refer to the contact information provided with your product or visit the official USARemote website for support resources.

Legal Disclaimer: This is a replacement aftermarket part.