Parkside PWS 125 D3

Download PDF
Contents

Parkside PWS 125 D3 Angle Grinder User Manual

Introduction

This manual provides essential information for the safe and effective operation, maintenance, and troubleshooting of your Parkside PWS 125 D3 Angle Grinder. Please read these instructions carefully before using the tool and keep them for future reference. Proper use and adherence to safety guidelines will ensure optimal performance and extend the life of your tool.

General Safety Instructions

WARNING: Read all safety warnings, instructions, illustrations, and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire, and/or serious injury.

Work Area Safety

  • Keep the work area clean and well-lit. Cluttered or dark areas invite accidents.
  • Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes.
  • Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

Electrical Safety

  • Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
  • Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges, and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
  • Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
  • Do not abuse the cord. Never use the cord for carrying, pulling, or unplugging the power tool. Keep cord away from heat, oil, sharp edges, or moving parts. Damaged or entangled cords increase the risk of electric shock.

Personal Safety

  • Always wear eye protection. Use safety glasses, goggles, or a face shield.
  • Wear hearing protection.
  • Wear appropriate dust mask if operations create dust.
  • Dress properly. Do not wear loose clothing or jewelry. Keep your hair and clothing away from moving parts.
  • Stay alert, watch what you are doing, and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol, or medication.

Power Tool Use and Care

  • Do not force the power tool. Use the correct power tool for your application.
  • Disconnect the plug from the power source before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
  • Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool.
  • Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use.

Specific Angle Grinder Safety

  • Always use the guard. Ensure the guard is securely attached and positioned for maximum safety.
  • Use only discs with the correct diameter and bore size.
  • Never use damaged or incorrect discs.
  • Ensure the disc is correctly mounted and tightened before use.
  • Do not use the tool for applications for which it is not intended.
  • Always hold the tool firmly with both hands during operation.
  • Be aware of kickback. Kickback is a sudden reaction to a pinched or snagged rotating wheel.

Product Overview

The Parkside PWS 125 D3 is a powerful angle grinder designed for cutting, grinding, and brushing various materials. It features variable speed control and a robust design for demanding tasks.

Components

Parkside PWS 125 D3 Angle Grinder

Image 1: The Parkside PWS 125 D3 Angle Grinder, showcasing its main body, disc guard, auxiliary handle, and power cord. The tool features a green and black housing with silver accents.

  1. Main Handle with Power Switch
  2. Variable Speed Control Dial
  3. Spindle Lock Button
  4. Disc Guard
  5. Grinding/Cutting Disc (accessory)
  6. Auxiliary Handle
  7. Power Cord

Included Accessories

Parkside PWS 125 D3 Angle Grinder Accessories

Image 2: Included accessories for the Parkside PWS 125 D3 Angle Grinder. This image displays a 125mm cutting disc, a clamping wrench for disc changes, and two replacement carbon brushes.

  • 1 x 125 mm Cutting Disc
  • 1 x Clamping Wrench
  • 2 x Replacement Carbon Brushes

Setup and Assembly

Attaching the Auxiliary Handle

The auxiliary handle can be attached in three different positions to suit your working preference and ensure optimal control.

Parkside PWS 125 D3 Angle Grinder with handle positions

Image 3: The Parkside PWS 125 D3 Angle Grinder demonstrating the three possible attachment positions for the auxiliary handle, providing flexibility for different tasks and user comfort.

  1. Screw the auxiliary handle firmly into one of the three threaded openings on the gear housing.
  2. Ensure it is securely tightened before operation.

Adjusting the Disc Guard

The disc guard is adjustable without tools to provide optimal protection for various applications.

  1. Loosen the quick-release lever on the disc guard.
  2. Rotate the guard to the desired position to protect against sparks and debris.
  3. Securely tighten the quick-release lever.

Installing/Changing Grinding or Cutting Discs

WARNING: Always disconnect the tool from the power supply before changing discs.

  1. Press and hold the spindle lock button (labeled as 3 in Image 1) to prevent the spindle from rotating.
  2. Using the clamping wrench, loosen the clamping nut by turning it counter-clockwise.
  3. Remove the clamping nut and the old disc.
  4. Place the new disc onto the spindle, ensuring it is correctly seated on the inner flange.
  5. Replace the clamping nut and tighten it firmly with the clamping wrench while holding the spindle lock button.
  6. Ensure the disc is securely fastened and rotates freely without wobbling.

Operating Instructions

Before starting, ensure all safety precautions are followed and the work area is clear.

User operating Parkside PWS 125 D3 Angle Grinder

Image 4: A user demonstrating the operation of the Parkside PWS 125 D3 Angle Grinder, wearing safety glasses and gloves, while cutting a metal bar. Sparks are visible, highlighting the importance of protective gear.

Switching On and Off

  1. To Switch On: Press the ON/OFF switch. For continuous operation, press the switch and then lock it into position.
  2. To Switch Off: Release the ON/OFF switch. If locked, press the switch briefly and release.

Variable Speed Control

The Parkside PWS 125 D3 features a continuously adjustable speed control dial (labeled as 2 in Image 1). Rotate the dial to select the desired speed (3,000 to 12,000 RPM) suitable for your material and application. Lower speeds are generally used for polishing or brushing, while higher speeds are for cutting and grinding.

Working Techniques

  • Grinding: Apply moderate pressure and move the grinder evenly over the workpiece. Do not press too hard, as this can overload the motor and damage the disc.
  • Cutting: Use a cutting disc and guide the tool slowly and steadily through the material. Avoid tilting the disc, which can cause it to bind or break.
  • Always ensure the workpiece is securely clamped.
  • Allow the disc to reach full speed before making contact with the workpiece.
  • After switching off, wait for the disc to stop completely before setting the tool down.

Maintenance and Care

Regular maintenance ensures the longevity and safe operation of your angle grinder.

Cleaning

  • Always disconnect the power plug before cleaning.
  • Keep the ventilation slots clean to prevent overheating. Use a brush or compressed air to remove dust and debris.
  • Do not use water or chemical cleaning agents. Wipe the tool with a dry cloth.

Replacing Carbon Brushes

The carbon brushes are wear parts and should be checked regularly. If the motor performance decreases significantly or excessive sparking occurs, the carbon brushes may need replacement.

  1. Disconnect the tool from the power supply.
  2. Locate the carbon brush caps on the motor housing.
  3. Unscrew the caps and carefully remove the old carbon brushes.
  4. Insert the new carbon brushes, ensuring they are correctly oriented.
  5. Screw the caps back on firmly.
  6. After replacement, run the tool at no load for a few minutes to allow the new brushes to seat properly.

Troubleshooting

This section addresses common issues you might encounter with your angle grinder.

ProblemPossible CauseSolution
Tool does not startNo power supply; Damaged power cord; Faulty switch; Worn carbon brushesCheck power connection; Inspect cord for damage; Contact service center; Replace carbon brushes
Excessive sparking at motorWorn carbon brushes; Motor overloadReplace carbon brushes; Reduce pressure during operation
Tool loses power during operationMotor overload; Loose connection; Worn carbon brushesReduce load; Check power cord connection; Replace carbon brushes
Unusual noise or vibrationDamaged disc; Loose components; Internal faultReplace disc; Check all fasteners; Discontinue use and contact service center

Technical Specifications

ModelParkside PWS 125 D3
Input Power1200 W
No-Load Speed3,000 - 12,000 RPM (continuously variable)
Disc DiameterUp to 125 mm
Spindle Thread(Not specified, common is M14)
Power Cable LengthApprox. 3 m
WeightApprox. 3.12 kg
Voltage230 V
Sound Level107 dB
MaterialAluminum housing

Warranty and Customer Support

For warranty claims, technical support, or spare parts, please contact the manufacturer or your authorized dealer. Keep your proof of purchase for warranty validation.

Please refer to the official Parkside website or your purchase documentation for specific warranty terms and contact information.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.