1. Introduction
This instruction manual provides detailed guidance for the installation, operation, and maintenance of your Anderic Universal Remote and Receiver Kit (Model RR7079TKIT). This kit is designed to convert most 3-speed ceiling fans into a wireless remote-controlled system, allowing you to adjust fan speeds and light settings conveniently.
Please read this manual thoroughly before beginning installation to ensure proper setup and safe operation.
2. Safety Information
WARNING: Risk of Electric Shock. Disconnect power at the circuit breaker or fuse box before installation or servicing.
- Always turn off the power supply to the ceiling fan at the main circuit breaker before attempting any installation, repair, or maintenance.
- Ensure all electrical connections are secure and comply with local electrical codes. If you are unsure about wiring, consult a qualified electrician.
- Do not use this kit with solid-state fan speed controls.
- The receiver is designed for indoor use only.
- Do not exceed the maximum electrical ratings of the receiver.
3. Package Contents
Verify that all components are present in your package:
- Anderic RR7079T Remote Control
- UC7067FMRX Receiver
- Remote Wall Mount Bracket
- Mounting Screws for Wall Bracket (typically 2)
- Wire Nuts (typically 4-5)
- Basic Installation Instructions (this manual provides comprehensive details)
Image: All components of the Anderic Universal Remote and Receiver Kit, including the white remote control, black receiver unit, two mounting screws, and four yellow wire nuts.
4. Setup and Installation
Follow these steps carefully to install the remote and receiver kit:
- Disconnect Power: Before starting, ensure the power to the ceiling fan is completely off at the circuit breaker or fuse box. Test the fan and light switch to confirm power is off.
- Access Fan Canopy: Carefully lower the ceiling fan canopy (the decorative cover that hides the wiring connections at the ceiling). You may need a screwdriver to loosen screws.
-
Identify Wiring: Inside the canopy, identify the existing wiring:
- Live (Hot) Wire (usually black or red from ceiling)
- Neutral Wire (usually white from ceiling)
- Fan Motor Wire (usually black from fan)
- Light Kit Wire (usually blue from fan)
- Ground Wire (usually green or bare copper)
-
Set Dip Switches: Both the remote control and the receiver have a set of dip switches (small switches labeled 1, 2, 3, 4). These switches must be set to the exact same pattern (ON or OFF) on both the remote and the receiver for them to communicate. Use a small screwdriver or pen to adjust them. This allows multiple remote kits to be used in one area without interference.
Image: The Anderic remote control and receiver unit. The receiver clearly shows the blue dip switch block with four switches labeled 1-4, which must be matched with the remote's internal dip switches.
-
Wire the Receiver: Connect the receiver wires to the corresponding fan and house wires using the provided wire nuts. Refer to the wiring diagram below:
Receiver Wiring Diagram Receiver Wire Color Connect To Description Black (AC IN L) House Live (Hot) Wire Power input from ceiling White (AC IN N) House Neutral Wire Power input from ceiling Blue (TO LIGHT) Fan Light Kit Wire Output to fan light Black (TO MOTOR L) Fan Motor Wire Output to fan motor Green (Ground) House Ground Wire Safety ground connection - Secure Receiver: Carefully tuck all wires and the receiver unit into the fan canopy. Ensure no wires are pinched and there is enough space for the receiver. The receiver is designed to fit inside most standard fan canopies.
- Reattach Canopy: Securely reattach the fan canopy to the ceiling bracket.
- Restore Power: Turn the power back on at the circuit breaker.
- Test Operation: Test the fan and light functions using the remote control.
5. Operating Instructions
The Anderic RR7079T remote control provides intuitive control over your ceiling fan and light:
Image: The Anderic RR7079T remote control, highlighting its buttons for fan speed and light control.
-
LIGHT / DIMMER Button:
- Press and release to turn the light ON or OFF.
- Press and hold to dim or brighten the light. Release when the desired brightness is reached.
- LO Button: Sets the fan speed to Low.
- MED Button: Sets the fan speed to Medium.
- HI Button: Sets the fan speed to High.
- FAN OFF Button: Turns the fan off.
6. Maintenance
The Anderic Universal Remote and Receiver Kit requires minimal maintenance.
- Battery Replacement: The remote control requires one 9V battery. When the remote's range decreases or it becomes unresponsive, it's time to replace the battery. To replace, slide open the battery compartment cover on the back of the remote, remove the old battery, insert a new 9V battery, and close the cover.
- Cleaning: Wipe the remote control and receiver (if accessible) with a soft, dry cloth. Do not use abrasive cleaners or immerse in water.
7. Troubleshooting
If you experience issues with your Anderic remote and receiver kit, try the following troubleshooting steps:
| Problem | Possible Cause | Solution |
|---|---|---|
| Fan/Light does not respond to remote. | No power to receiver; Incorrect dip switch settings; Dead battery in remote; Loose wiring connection. |
|
| Fan operates, but light does not. | Light bulb issue; Incorrect light wiring; Light limit switch (if applicable). |
|
| Fan operates at wrong speed or inconsistently. | Interference from other devices; Incorrect dip switch settings. |
|
8. Specifications
| Feature | Detail |
|---|---|
| Model Number | RR7079TKIT |
| Remote Control Model | RR7079T |
| Receiver Model | UC7067FMRX |
| Compatible Devices | 3-Speed Ceiling Fans (most models) |
| Connectivity Technology | Infrared (IR) |
| Max Number of Supported Devices | 1 (per kit) |
| Remote Battery Type | 1 x 9V battery (not included) |
| Package Dimensions | 7.01 x 2.99 x 2.4 inches |
| Item Weight | 7.2 ounces |
| Manufacturer | Dan's Electronics Etc., Inc. |
9. Warranty Information
Warranty coverage for the Anderic Universal Remote and Receiver Kit is typically provided by the manufacturer, Dan's Electronics Etc., Inc., or the seller at the time of purchase. Please refer to the warranty card included with your product, the product packaging, or the official Anderic website for specific warranty terms and conditions. Keep your proof of purchase for warranty claims.
10. Customer Support
For further assistance, technical support, or inquiries regarding your Anderic Universal Remote and Receiver Kit, please contact Anderic customer support. You can typically find contact information on the official Anderic website or through the retailer where you purchased the product.
Visit the Anderic Store on Amazon for more information and products.
