Introduction
This manual provides essential information for the proper use and understanding of your RadioShack 2711131 100-kohm 1/2-Watt Carbon-Film Resistors. Please read these instructions carefully before use to ensure safe and effective application in your electronic projects.
Product Overview
The RadioShack 2711131 resistors are passive two-terminal electrical components designed to implement electrical resistance in an electronic circuit. These are carbon-film resistors, known for their stable performance and wide range of applications in general electronics. This pack contains five individual resistors.

Figure 1: A single RadioShack 100-kohm 1/2-Watt Carbon-Film Resistor. This image displays the cylindrical body of the resistor with axial leads extending from both ends, and color bands indicating its resistance value and tolerance.
Setup and Installation
Resistors are fundamental components in electronic circuits. Proper installation is crucial for circuit functionality and safety.
Preparation:
- Identify Resistance Value: Use the color code bands on the resistor body to verify the 100-kohm resistance and 1/2-Watt power rating.
- Circuit Design: Ensure the resistor's specifications (resistance, power rating) match your circuit design requirements.
- Tools: Prepare necessary tools such as a soldering iron, solder, wire cutters, and a breadboard or PCB.
Installation Steps:
- Placement: Insert the resistor leads into the designated holes on your breadboard or Printed Circuit Board (PCB). Ensure correct placement according to your circuit diagram.
- Bending Leads: Gently bend the leads to secure the resistor in place if soldering. Avoid sharp bends near the resistor body.
- Soldering (if applicable): If using a PCB, solder the leads to the copper pads. Apply heat to the pad and lead simultaneously, then introduce solder. Ensure a good, shiny solder joint.
- Trimming Leads: After soldering, trim any excess lead length using wire cutters to prevent short circuits.
Safety Note: Always disconnect power from the circuit before installing or removing components. Wear appropriate safety gear, such as safety glasses, when soldering.
Operating Principles
Resistors operate based on Ohm's Law, which states that the current through a conductor between two points is directly proportional to the voltage across the two points. The constant of proportionality is the resistance.
- Ohm's Law: V = I * R (Voltage = Current * Resistance)
- Power Dissipation: Resistors dissipate electrical energy as heat. The power dissipated (P) can be calculated using P = V * I, P = I² * R, or P = V² / R. These resistors are rated for 1/2-Watt, meaning they can safely dissipate up to 0.5 Watts of power. Exceeding this rating can cause the resistor to overheat and fail.
- Function: In a circuit, resistors are used to limit current, divide voltage, bias active components, and terminate transmission lines, among other applications.
Maintenance
Carbon-film resistors are passive components and generally require no routine maintenance. However, proper handling and storage are recommended to ensure their longevity and performance.
- Storage: Store resistors in a dry, cool environment, away from direct sunlight and corrosive chemicals. Keep them in their original packaging or in anti-static bags to prevent physical damage and contamination.
- Handling: Avoid excessive bending of the leads close to the resistor body, as this can cause internal damage.
- Inspection: Periodically inspect resistors in active circuits for signs of overheating (discoloration, charring) or physical damage.
Troubleshooting
While resistors are highly reliable, issues can arise due to incorrect application or external factors.
- Incorrect Resistance Reading:
- Cause: Wrong resistor value selected, manufacturing defect, or damage.
- Solution: Verify the color code. Measure resistance with a multimeter before installation. Replace if faulty.
- Overheating/Burning:
- Cause: Exceeding the resistor's power rating (1/2-Watt). Too much current flowing through it.
- Solution: Re-evaluate circuit design. Use a resistor with a higher power rating or a different resistance value to limit current.
- Open Circuit (No Conductivity):
- Cause: Physical damage to the resistor body or leads, poor solder joint, internal break.
- Solution: Inspect for visible damage. Check solder joints. Test continuity with a multimeter. Replace the resistor.
Specifications
| Feature | Detail |
|---|---|
| Brand | RadioShack |
| Model Number | 2711131 |
| Resistance | 100 kΩ (100,000 ohms) |
| Power Rating | 1/2 Watt (0.5 W) |
| Type | Carbon-Film Resistor |
| Package Quantity | 5 Pack |
| Item Weight | 3.52 ounces (for the pack) |
| Package Dimensions | 4 x 2 x 0.2 inches |
| ASIN | B06XCJWC6Q |
Warranty and Support
Specific warranty details for this product are not provided in the available information. For warranty claims, technical support, or further inquiries, please refer to the official RadioShack website or contact their customer service directly.
You may also consult the retailer where the product was purchased for their return and support policies.