Anderic RR7080T

Anderic UC7080T Remote Control User Manual

Model: RR7080T

Introduction

This manual provides comprehensive instructions for the Anderic RR7080T remote control, designed as a direct replacement for original equipment Hampton Bay and Harbor Breeze ceiling fan remotes, including models like UC7080T and CHQ7080T. This remote offers full control over your ceiling fan's functions, including fan speed, light operation with dimming, and fan direction reversal.

Anderic RR7080T remote control, angled view

Figure 1: Angled view of the Anderic RR7080T remote control, showing the layout of its buttons for fan speed, light, and reverse functions.

Setup and Installation

The Anderic RR7080T remote control requires alignment of its dip-switches to match the pattern of your ceiling fan receiver. This unit has 16 different code combinations. Before beginning, ensure your fan is operated in "HIGH SPEED" and the light is in the "ON" condition at the switch knob.

1. Setting the Code on the Remote (Transmitter)

  1. Remove the battery cover. Press firmly below the arrow and slide the battery cover off.
  2. Slide the code switches to your desired up or down position. The factory setting is all up; do not use this position. Use a small screwdriver or a ballpoint pen to slide firmly up or down.
  3. Replace the battery cover on the transmitter.

2. Setting the Code on the Receiver

  1. Slide the code switches on your fan's receiver to the exact same positions as set on your remote (transmitter).

Note: The remote and receiver depicted in images may look different than your actual product, but the dip switch concept remains the same.

Diagram showing dip switch settings on the remote and receiver

Figure 2: Installation and operating instructions diagram, illustrating how to set the code switches on both the remote (transmitter) and the ceiling fan receiver.

Back view of Anderic RR7080T remote with battery compartment open and wall mount bracket

Figure 3: Rear view of the Anderic RR7080T remote control with the battery cover removed, revealing the battery compartment and dip switches. The included wall mount bracket is also visible.

Operating Instructions

The Anderic RR7080T remote provides intuitive control over your ceiling fan and light functions. Familiarize yourself with the button layout for optimal use.

  • LIGHT / DIMMER: Press to turn the light on or off. Press and hold to dim or brighten the light. This remote supports light dimming.
  • HI: Sets the fan speed to High.
  • MED: Sets the fan speed to Medium.
  • LO: Sets the fan speed to Low.
  • FAN OFF: Turns the fan off.
  • REVERSE: Changes the direction of the fan blades. This is useful for circulating air differently in summer (downward airflow) versus winter (upward airflow).
Front view of Anderic RR7080T remote control

Figure 4: Front view of the Anderic RR7080T remote control, clearly showing all control buttons for fan speed, light, and reverse functions.

Maintenance

Battery Replacement

The Anderic RR7080T remote control requires one 9V battery. When the remote's performance degrades or it stops responding, it's likely time to replace the battery.

  1. Slide off the battery cover located on the back of the remote.
  2. Remove the old 9V battery.
  3. Insert a new 9V battery, ensuring correct polarity (+/-).
  4. Slide the battery cover back into place until it clicks securely.

Dispose of old batteries responsibly according to local regulations.

Troubleshooting

If your Anderic RR7080T remote control is not functioning as expected, please refer to the following common issues and solutions:

ProblemPossible Cause / Solution
Remote not responding
  • Check battery: Ensure the 9V battery is new and correctly installed.
  • Dip switches: Verify that the dip switches on both the remote and receiver are set to the exact same pattern.
  • Distance: Ensure you are within range of the receiver.
Light not dimming
  • Bulb compatibility: Ensure your light bulbs are dimmable.
  • Hold button: Press and hold the LIGHT/DIMMER button to activate dimming. A quick press will only toggle on/off.
Fan not changing speed or direction
  • Dip switches: Re-check the dip switch settings on both units.
  • Receiver issue: The issue might be with the fan's receiver unit, not the remote.

Specifications

  • Model Number: RR7080T
  • Product Dimensions: 3.1 x 1.3 x 6.6 inches
  • Item Weight: 0.01 ounces
  • Battery Requirement: 1 x 9V battery (not included)
  • Compatible Receivers: UC7051G (and others compatible with UC7080T/CHQ7080T)
  • Functions: Downlights (with dimming), Uplights, Reverse, Fan off, Fan speed (Low, Medium, High)
  • Color: White

Warranty and Support

Anderic is committed to providing high-quality replacement remote controls and accessories. This product is designed to meet stringent quality standards.

For support, please visit our website or contact us directly:

Please retain your proof of purchase for any warranty claims.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.