Skar Audio EVL-10 D2

Download PDF
Contents

Skar Audio EVL-10 D2 10-inch Car Subwoofer Instruction Manual

Model: EVL-10 D2

Introduction

This manual provides essential information for the proper installation, operation, and maintenance of your Skar Audio EVL-10 D2 10-inch Car Subwoofer. Please read this manual thoroughly before attempting installation or use to ensure optimal performance and product longevity.

Skar Audio EVL-10 D2 10-inch Subwoofer, angled view

Image: Angled view of the Skar Audio EVL-10 D2 10-inch subwoofer, showcasing its cone and robust construction.

Product Features

  • Peak Power: 2,000 Watts
  • RMS Power: 1,000 Watts
  • Voice Coil: 3-inch High Temperature Dual 2 Ohm with Black Coating
  • Cone: Competition Grade Paper Cone
  • Surround: High Roll Foam Surround
  • Suspension: Premium Suspension featuring the EVL Series Signature Red Two Layer Spider
  • Bass Output: Designed for deep, low, and extremely responsive bass
  • Sensitivity: 82.1 dB
  • Frequency Response Range: 28 Hz - 300 Hz
  • Xmax: 23.5 mm (one-way)

Specifications

Model NameEVL-10 D2
Speaker TypeSubwoofer
Subwoofer Diameter10 Inches
ImpedanceDual 2 Ohm
Peak Power2000 Watts
RMS Power1000 Watts
Frequency Response28 Hz - 300 Hz
Sensitivity82.1 dB
Voice Coil3-inch High Temperature
Product Dimensions12"D x 12"W x 12"H (Approximate, likely packaging dimensions)
Item Weight31.7 pounds
Connectivity TechnologyWired
Recommended UsesCar Audio Systems

Note: All specifications are subject to change without notice.

Setup and Installation

Proper installation is crucial for the performance and longevity of your subwoofer. It is highly recommended that installation be performed by a qualified professional.

1. Enclosure Selection

The EVL-10 D2 subwoofer is designed to perform optimally in a properly constructed enclosure. Consult Skar Audio's official website or a car audio specialist for recommended enclosure types (sealed or ported) and dimensions for this specific model. An incorrect enclosure can severely limit performance and potentially damage the subwoofer.

2. Wiring Configuration

The EVL-10 D2 features a dual 2 Ohm voice coil. This allows for various wiring configurations to match your amplifier's impedance requirements. Common configurations include:

  • Series Wiring: Connect the two 2 Ohm voice coils in series for a total impedance of 4 Ohms.
  • Parallel Wiring: Connect the two 2 Ohm voice coils in parallel for a total impedance of 1 Ohm.

Caution: Always ensure your amplifier is stable at the chosen impedance. Incorrect wiring can lead to amplifier damage or poor subwoofer performance. Refer to your amplifier's manual for compatible impedance loads.

Skar Audio EVL-10 D2 Subwoofer close-up of terminals

Image: Close-up view of the Skar Audio EVL-10 D2 subwoofer's spring-loaded terminals, indicating positive and negative connections for wiring.

3. Amplifier Matching

Select an amplifier that can deliver 1000 Watts RMS power at the chosen impedance. Using an underpowered or overpowered amplifier can lead to damage.

Skar Audio EVL-10 D2 Subwoofer side view showing magnet and cooling vents

Image: Side view of the Skar Audio EVL-10 D2 subwoofer, illustrating the large magnet structure and integrated cooling vents for thermal management.

4. Secure Mounting

Mount the subwoofer securely within its enclosure using appropriate fasteners. Ensure there are no air leaks around the mounting surface.

Operating Instructions

1. Break-in Period

Allow a break-in period of approximately 20-30 hours of normal listening before operating the subwoofer at high volumes. This allows the suspension components to loosen and reach their optimal performance characteristics. During this period, avoid playing the subwoofer at maximum volume or with excessive bass boost.

2. Amplifier Gain Settings

Properly set your amplifier's gain to match the output voltage of your head unit. Incorrect gain settings can lead to clipping and distortion, which can damage the subwoofer. Consult your amplifier's manual for detailed gain setting procedures.

3. Crossover Settings

Utilize your amplifier's or head unit's low-pass filter (LPF) to send only low frequencies to the subwoofer. A typical LPF setting for a 10-inch subwoofer is between 60 Hz and 100 Hz. Experiment with settings to achieve the best sound integration with your full-range speakers.

4. Avoiding Over-driving

Listen for signs of distortion or "bottoming out" (when the voice coil hits the back plate). If you hear these, reduce the volume or bass boost immediately to prevent damage. Prolonged operation with distortion will lead to premature failure.

Maintenance

The Skar Audio EVL-10 D2 subwoofer requires minimal maintenance.

  • Cleaning: Periodically wipe down the cone and surround with a soft, dry cloth to remove dust and debris. Avoid using harsh chemicals or excessive moisture.
  • Inspection: Regularly inspect the subwoofer for any signs of damage to the cone, surround, or voice coil leads. Ensure all mounting screws remain tight.
  • Environment: Protect the subwoofer from extreme temperatures, direct sunlight, and moisture.
Skar Audio EVL-10 D2 Subwoofer top view

Image: Top-down view of the Skar Audio EVL-10 D2 subwoofer, showing the cone and surround, which should be kept clean.

Troubleshooting

If you experience issues with your subwoofer, refer to the following common troubleshooting steps:

  1. No Sound:
    • Check all wiring connections (power, ground, remote, speaker wires) for secure contact.
    • Verify the amplifier is powered on (power indicator light).
    • Ensure the head unit is sending an audio signal.
    • Check for blown fuses in the amplifier or power distribution block.
    • Confirm correct impedance matching between subwoofer and amplifier.
  2. Distorted Sound:
    • Reduce amplifier gain settings to prevent clipping.
    • Check for proper crossover settings (LPF).
    • Inspect speaker wires for shorts or damage.
    • Ensure the subwoofer is not over-driven (reduce volume).
    • Verify the enclosure is sealed properly (if applicable) and free of rattles.
  3. Weak or Muffled Bass:
    • Check wiring polarity (+/-) for both the subwoofer and amplifier.
    • Verify enclosure volume and tuning are appropriate for the subwoofer.
    • Adjust amplifier gain and bass boost settings.
    • Ensure LPF is set correctly.
  4. Overheating Amplifier:
    • Check subwoofer impedance against amplifier's minimum stable impedance.
    • Ensure adequate ventilation for the amplifier.
    • Reduce amplifier gain or overall volume.

If troubleshooting steps do not resolve the issue, contact Skar Audio customer support or a qualified car audio technician.

Warranty Information

The Skar Audio EVL-10 D2 subwoofer comes with a Limited Warranty. Specific terms and conditions of the warranty, including coverage duration and claim procedures, are available on the official Skar Audio website or by contacting their customer service department. Please retain your proof of purchase for warranty claims.

The warranty typically covers manufacturing defects but does not cover damage resulting from improper installation, abuse, accidental damage, or unauthorized modifications.

Support and Contact

For further assistance, technical support, or warranty inquiries, please contact Skar Audio directly.

  • Official Website: Visit the Skar Audio Store on Amazon or their main website for product information, FAQs, and support resources.
  • Customer Service: Refer to the Skar Audio website for current contact methods, including phone numbers and email addresses.

© 2023 Skar Audio. All rights reserved. Information subject to change.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.