Teamson Home Round Steel Outdoor Fire Pit (Model CU296) Instruction Manual

1. Introduction

This manual provides essential information for the safe and effective use of your Teamson Home 30-inch Round Steel Outdoor Wood Burning Fire Pit. Please read all instructions carefully before assembly and operation to ensure proper function and safety.

The Teamson Home fire pit is designed to bring warmth and ambiance to your outdoor living space. Its sturdy steel construction and mesh design allow for efficient wood burning, while the included spark screen and poker enhance safety and ease of use.

2. Safety Information

WARNING: For outdoor use only. Do not use on wooden decks or other flammable surfaces. Keep children and pets away from the fire pit.

• Always place the fire pit on a flat, non-combustible surface.
• Ensure adequate clearance from structures, trees, and other flammable materials.
• Never leave a burning fire unattended.
• Use a spark screen to contain embers and sparks.
• Have a fire extinguisher, water hose, or sand readily available in case of emergency.
• Allow the fire pit to cool completely before cleaning or moving.
• Do not use gasoline, kerosene, or alcohol to start or rekindle a fire.
• Only burn seasoned natural wood. Do not burn trash, leaves, paper, or other combustible materials.
• Wear appropriate protective gear (gloves, long sleeves) when handling the fire pit or tending the fire.

3. Package Contents

Verify that all components are present before beginning assembly:

• Fire Bowl (1)
• Legs (4)
• Outer Ring Sections (multiple, to form a complete ring)
• Spark Screen (1)
• Poker (1)
• Assembly Hardware (bolts, nuts, washers)
• Assembly Tool (wrench, screwdriver - may not be included, a screwdriver is often needed)

Note: A screwdriver may be required for assembly and is not always included.

4. Setup and Assembly

Follow these steps to assemble your fire pit. It is recommended to have a second person assist with assembly, especially for attaching the outer ring.

1. Unpack Components: Carefully remove all parts from the packaging. Lay them out on a clean, soft surface to prevent scratches.
2. Attach Legs: Secure the four legs to the bottom of the fire bowl using the provided hardware. Ensure they are firmly attached but do not overtighten initially.
3. Assemble Outer Ring: Connect the sections of the outer ring around the top edge of the fire bowl. Loosely attach all sections before tightening any bolts. This allows for easier alignment. Once all sections are in place, gradually tighten all bolts in a cross pattern until secure.
4. Attach Spark Screen Handle: Secure the handle to the top of the spark screen using the provided hardware.
5. Final Check: Ensure all connections are tight and the fire pit is stable before use.

5. Operating Instructions

This fire pit is designed for burning wood and can also be used for barbecuing.

5.1. Wood Burning

1. Placement: Position the fire pit on a level, non-combustible surface, away from any flammable materials.
2. Fuel: Place seasoned firewood onto the bottom of the fire bowl. Do not overfill.
3. Ignition: Use appropriate fire starters to ignite the wood. Never use flammable liquids.
4. Spark Screen: Once the fire is lit, carefully place the spark screen over the fire bowl to contain sparks and embers. Use the poker to adjust the screen or logs as needed.
5. Extinguishing: Allow the fire to burn down naturally. Do not use water to extinguish the fire as this can damage the fire pit and create hazardous steam. Ensure all embers are completely extinguished before leaving unattended.

5.2. Barbecuing (if applicable)

This fire pit features a versatile design that allows for use as a barbecue grill.

1. Prepare Coals: Build a wood fire or use charcoal in the fire bowl. Allow coals to reach an even temperature before placing food on the grill.
2. Position Grill Grate: Place the grill grate over the hot coals. Adjust its height or position as needed for desired cooking temperature.
3. Cooking: Place food directly on the grill grate. Monitor cooking closely.
4. After Use: Remove the grill grate once cooking is complete. Allow the fire to extinguish as per wood burning instructions.

6. Maintenance

Regular maintenance will extend the life of your fire pit.

• Cleaning: After the fire pit has completely cooled, remove ashes and debris from the fire bowl. Use a stiff brush to clean the interior and exterior surfaces.
• Rust Prevention: The steel construction is durable, but exposure to elements can lead to rust. Store the fire pit in a dry area or use a weather-resistant cover when not in use. Periodically apply a high-temperature paint to touch up any chipped areas.
• Storage: During prolonged periods of non-use, especially in harsh weather, store the fire pit indoors or under a protective cover.

7. Troubleshooting

If you encounter issues with your fire pit, consider the following:

• Poor Airflow/Smoke: Ensure the fire pit is not overfilled with wood. The mesh design allows for good airflow; clear any blockages. Use dry, seasoned wood for optimal burning.
• Rust: Surface rust can occur over time, especially if exposed to moisture. This is normal for steel products. Clean affected areas and apply high-temperature rust-resistant paint.
• Instability: Check all bolts and connections to ensure they are tightened securely. Ensure the fire pit is placed on a flat, stable surface.

8. Specifications

9. Warranty and Support

This product comes with a 30-day return policy. For further support or warranty claims, please contact Teamson Home customer service.