Introduction
This manual provides comprehensive instructions for the Anderic Replacement FAN-9T Thermostatic Remote Control, designed specifically for Hampton Bay ceiling fans.
Image: Front view of the Anderic FAN-9T remote control, showing the display and various control buttons.
Compatibility
The Anderic FAN-9T remote control is compatible with Hampton Bay ceiling fans. To ensure compatibility, verify that your original remote control has "FAN-9T" printed on its back. This remote features FCC ID: L3HFAN9T and PN: FAN9TR.
Important Note: This remote control provides on/off functionality for lights and does not support dimming. If your original remote for a Windward II 54-inch Ceiling Fan has a model number starting with "CHQ" (located on the back), you may require the RR7096TR model with a yellow light button, even if your original has a green light button.
Key Features
- Reverse Operation: Easily switch the ceiling fan's rotation direction for optimal airflow in different seasons.
- Thermostatic Function: Set a desired temperature, and the remote will automatically adjust fan speed to maintain a comfortable environment.
- Lights On/Off Control: Conveniently turn your ceiling fan's lights on or off with a dedicated button.
- Temperature Conversion: Switch between Celsius and Fahrenheit temperature displays by holding the TEMP UP and TEMP DOWN buttons simultaneously for 3 seconds.
- Wall Mount Holder: Includes a wall mount holder for convenient storage and accessibility of the remote.
Setup Instructions
Before using your new Anderic FAN-9T remote control, follow these steps to install batteries and set the correct code for your ceiling fan receiver.
1. Battery Installation
- Remove the battery cover located on the back of the remote control. Press firmly below the arrow and slide the cover off.
- Insert four (4) AAA batteries, ensuring correct polarity (+/-).
- Replace the battery cover.
Image: Rear view of the remote control with the battery cover removed, revealing the battery slots and DIP switches.
2. Setting the Code (DIP Switches)
The remote control and your ceiling fan receiver must be set to the same code for proper communication. This unit has 16 different code combinations. Ensure your fan is operated in "HIGH SPEED" and the light is in "ON" condition at the switch knob before proceeding.
- Setting the code on the remote:
- With the battery cover removed, locate the DIP switches inside the battery compartment.
- Slide the code switches to your desired up or down position. (Factory setting is all up. Do not use this position unless it matches your receiver.) Use a small screwdriver or a ballpoint pen to firmly slide the switches.
- Replace the battery cover on the transmitter (remote).
- Setting the code on the receiver:
- Locate the receiver unit within your ceiling fan assembly.
- Slide the code switches on the receiver to the exact same positions (up/down) as you set on your remote control.
Image: Diagram illustrating how to set the code switches on both the remote control (transmitter) and the ceiling fan receiver.
Once both the remote and receiver codes are matched, your remote control should be ready for operation.
Operating Instructions
Familiarize yourself with the buttons on your Anderic FAN-9T remote control to operate your ceiling fan effectively.
Image: Angled view of the Anderic FAN-9T remote control, highlighting the button layout.
- Fan Speed Control: Use the "MANUAL LOW" and "HIGH" indicators on the display to adjust fan speed. The remote automatically adjusts fan speed in thermostatic mode.
- FAN AUTO Button: Activates or deactivates the automatic fan speed adjustment based on the set temperature.
- FOR/REV Button: Press this button to change the direction of the fan blades (forward for cooling, reverse for heat circulation).
- Light Button: Press to turn the ceiling fan lights ON or OFF. (Note: This remote does not support dimming.)
- TIMER Button: Activates the fan timer function. Refer to your fan's specific instructions for timer settings.
- LIGHT DELAY Button: Activates the light delay function. Refer to your fan's specific instructions for light delay settings.
- TEMP UP / TEMP DOWN Buttons: Adjust the desired temperature setting for the thermostatic function.
- Temperature Unit Conversion (C/F): To switch between Celsius and Fahrenheit, hold down the TEMP UP and TEMP DOWN buttons simultaneously for 3 seconds.
Maintenance
- Cleaning: Wipe the remote control with a soft, dry cloth. Do not use abrasive cleaners or solvents.
- Battery Replacement: Replace batteries when the remote's performance degrades or the display becomes dim. Always use new AAA batteries and dispose of old batteries responsibly.
- Storage: When not in use for extended periods, remove batteries to prevent leakage. Store the remote in a cool, dry place.
Image: The Anderic FAN-9T remote control securely placed in its included wall mount holder.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Remote not responding / Fan not working. |
|
|
| Lights not working. |
|
|
| Temperature display is incorrect. | Incorrect temperature unit setting. | Hold TEMP UP and TEMP DOWN buttons simultaneously for 3 seconds to switch between Celsius and Fahrenheit. |
Specifications
| Attribute | Detail |
|---|---|
| Product Dimensions | 3 x 1 x 6 inches |
| Item Weight | 4.8 ounces |
| Model Number | FAN9T |
| Batteries Required | 4 AAA batteries |
| Color | White |
| Compatible Devices | Hampton Bay Ceiling Fans |
| FCC ID | L3HFAN9T |
| PN | FAN9TR |
Support Information
Anderic is committed to providing high-quality replacement remote controls and accessories. For further assistance or inquiries, please refer to the official Anderic website or contact their customer support.
Anderic is a company based in NC, USA, dedicated to ensuring the highest quality standards for their products.
