LEVOIT Kyra Himalayan Salt Lamp

Introduction

The LEVOIT Kyra Himalayan Salt Lamp is crafted from natural Himalayan salt crystals, designed to provide a warm, ambient glow. This manual provides essential information for the safe and effective use of your salt lamp.

Package Contents

• 1 x LEVOIT Kyra Himalayan Salt Lamp Crystal Rock
• 1 x 6.5 Ft UL-Listed Power Cord with Touch Brightness Dimmer Switch
• 3 x C7 15 Watt Incandescent Light Bulbs (one pre-installed, two extra)
• 1 x User Manual

Safety Instructions

• Electrical Safety: Ensure the power input is 120V/60Hz. Use only the provided UL-listed power cord and bulbs. Do not use the lamp with damaged cords or plugs.
• Moisture Warning: Himalayan salt is hygroscopic, meaning it absorbs moisture from the air. Place the lamp in a dry environment. If the lamp becomes moist, turn it on to a high setting to allow the heat from the bulb to dry the crystal.
• Placement: Place the lamp on a stable, water-resistant surface to protect furniture from potential moisture build-up.
• Handling: Handle the salt crystal with care as it can be fragile.
• Children and Pets: Keep the lamp out of reach of children and pets to prevent accidental damage or ingestion of salt.

Setup

1. Carefully remove the salt lamp and all components from the packaging.
2. Place the salt crystal securely onto the stainless steel base.
3. Ensure the pre-installed C7 15W bulb is properly seated in the E12 socket.
4. Place the lamp on a flat, stable surface.
5. Plug the ETL certified power cord into a standard 120V/60Hz electrical outlet.

Image: The LEVOIT Kyra Himalayan Salt Lamp with its natural crystal rock and stainless steel base, ready for setup.

Operating Instructions

The LEVOIT Kyra Himalayan Salt Lamp features a touch dimmer switch for easy control of brightness.

1. Turning On/Off: Lightly tap the touch dimmer switch once to turn the lamp on or off.
2. Adjusting Brightness: While the lamp is on, press and hold the touch dimmer switch. The brightness will gradually increase or decrease. Release the switch when the desired brightness level is reached.

Image: A hand operating the touch dimmer switch on the lamp's power cord, illustrating how to adjust brightness.

Maintenance

Cleaning

Regularly dust the salt crystal with a dry, clean cloth. If the crystal becomes moist, turn the lamp on to a high setting for several hours to dry it out.

Bulb Replacement

If the bulb needs replacement, use only C7 15W incandescent light bulbs with an E12 socket. Two extra bulbs are included in your package.

1. Unplug the lamp from the power outlet.
2. Carefully flip the lamp over.
3. Remove the four screws from the base using a small screwdriver.
4. Gently slide off the base while holding the salt crystal.
5. Carefully set the salt crystal aside.
6. Remove the old bulb from its socket.
7. Install the new C7 15W bulb into the socket.
8. Align the base back onto the salt crystal, ensuring the screw holes are aligned.
9. Replace and tighten all four screws.

Troubleshooting

• Lamp does not turn on: Check if the power cord is securely plugged into the outlet and the lamp. Ensure the bulb is properly seated and not burnt out. Try a different outlet.
• Lamp is dim or flickers: The bulb may be loose or nearing the end of its life. Replace the bulb if necessary.
• Lamp is sweating/moist: This is normal for salt lamps in humid environments. Turn the lamp to a high brightness setting and leave it on for several hours to dry the crystal. Ensure the lamp is placed in a dry area.
• Touch dimmer is unresponsive: Ensure your hands are clean and dry when operating the touch switch. If the issue persists, unplug the lamp for a few minutes and then plug it back in.

Specifications

Warranty and Support

For warranty information or product support, please refer to the warranty card included in your package or contact LEVOIT customer service directly. Keep your purchase receipt for warranty claims.