Fisher & Paykel 900ICON208

Fisher & Paykel ICON Series ThermoSmart Breathing Tube User Manual

Model: 900ICON208

1. Introduction

This manual provides essential information for the proper use and maintenance of your Fisher & Paykel ICON Series ThermoSmart Breathing Tube, Model 900ICON208. This heated breathing tube is designed to work exclusively with Fisher & Paykel ICON Series CPAP machines, including Auto, Novo, and Premo models.

The ThermoSmart technology integrates an internal heated coil to prevent condensation (rainout) within the hose and ensures the delivery of optimal temperature and humidity levels to the user, independent of ambient air conditions.

2. Safety Information

Please read all instructions carefully before using the ThermoSmart Breathing Tube. Failure to follow these instructions may result in improper operation or injury.

  • Use this breathing tube only with compatible Fisher & Paykel ICON Series CPAP devices as specified.
  • Do not attempt to modify the breathing tube in any way. Unauthorized modifications may compromise performance and safety.
  • Inspect the tube regularly for any signs of damage, cracks, or unusual odors. Discontinue use and replace if any issues are detected.
  • Keep the breathing tube away from pets and young children to prevent damage or misuse.
  • Ensure all connections are secure before operating the CPAP machine.

3. Package Contents

Your package should contain the following item:

  • One (1) Fisher & Paykel ICON Series ThermoSmart Breathing Tube (6 ft length).

4. Setup

Follow these steps to properly connect your ThermoSmart Breathing Tube:

  1. Ensure your Fisher & Paykel ICON Series CPAP machine is turned off and unplugged from the power source.
  2. Locate the air outlet port on your CPAP machine.
  3. Connect one end of the ThermoSmart Breathing Tube firmly to the air outlet port of the CPAP machine. Ensure a snug fit to prevent air leaks.
  4. Connect the other end of the ThermoSmart Breathing Tube to your CPAP mask. Again, ensure a secure connection.
  5. Once connected, you may plug in and power on your CPAP machine.
Fisher & Paykel ICON Series ThermoSmart Breathing Tube connected to a CPAP machine.

Image 1: The Fisher & Paykel ICON Series ThermoSmart Breathing Tube. This image shows the coiled heated tube, designed for optimal temperature and humidity delivery with compatible CPAP machines.

5. Operation

The Fisher & Paykel ICON Series ThermoSmart Breathing Tube operates automatically once connected to a compatible ICON Series CPAP machine. The integrated ThermoSmart technology will regulate the temperature within the tube to prevent condensation and maintain consistent humidification.

  • Ensure the CPAP machine is powered on and therapy has started.
  • No manual adjustments are typically required for the breathing tube itself. The CPAP machine's settings will control the humidification and heating levels.
  • If you experience discomfort or issues with temperature/humidity, consult your CPAP machine's user manual or contact your healthcare provider.

6. Maintenance

Cleaning Instructions

Regular cleaning of your ThermoSmart Breathing Tube is crucial for hygiene and optimal performance.

  1. Disconnect the breathing tube from both the CPAP machine and the mask.
  2. Wash the tube gently with warm water and a mild, non-abrasive soap. Avoid harsh chemicals or strong detergents.
  3. Rinse the tube thoroughly under running water to remove all soap residue.
  4. Hang the tube to air dry completely before re-connecting it to your CPAP system. Ensure no moisture remains inside the tube.

Replacement

The ThermoSmart Breathing Tube is a consumable item and should be replaced periodically. Replace the tube if you observe any of the following:

  • Visible cracks, tears, or holes in the tubing.
  • Persistent unusual odors, even after cleaning.
  • Reduced heating effectiveness or increased condensation (rainout).
  • General wear and tear that may affect its integrity or performance.

Typical replacement frequency varies, but it is generally recommended to replace breathing tubes every 6 to 12 months, or sooner if damage is evident.

7. Troubleshooting

Problem Possible Cause Solution
Excessive condensation (rainout) in the tube. Tube not properly connected, tube damaged, or CPAP machine's humidification settings are too high for ambient conditions.
  • Ensure the tube is securely connected to both the CPAP machine and the mask.
  • Inspect the tube for any damage. Replace if necessary.
  • Consult your CPAP machine's manual to adjust humidification settings.
No heat felt from the tube. Tube not properly connected, tube damaged, or CPAP machine's heated tube function is not activated or faulty.
  • Verify secure connections.
  • Check your CPAP machine's settings to ensure the heated tube function is enabled.
  • If the issue persists, the tube may be faulty and require replacement.
Unusual or chemical odor from the tube. New tube odor (should dissipate), or material degradation/contamination.
  • Clean the tube thoroughly as per maintenance instructions.
  • If the odor persists after cleaning or is strong and unpleasant, discontinue use immediately and replace the tube.

If you encounter problems not listed here or if troubleshooting steps do not resolve the issue, contact your equipment provider or healthcare professional.

8. Specifications

Model Number 900ICON208
Product Dimensions 76.5 x 1 x 1 inches (approximately 6 ft length)
Item Weight 5.22 ounces
Compatibility Fisher & Paykel ICON Series CPAP machines (Auto, Novo, Premo Models)
Manufacturer PHILIPS RESPIRONICS
Date First Available February 16, 2017

9. Warranty and Support

Specific warranty terms for the Fisher & Paykel ICON Series ThermoSmart Breathing Tube are provided by the manufacturer or your authorized dealer at the time of purchase. Please retain your proof of purchase for warranty claims.

For technical assistance, product inquiries, or to report issues, please contact your authorized Fisher & Paykel dealer or the manufacturer directly. Contact information can typically be found on the product packaging or the manufacturer's official website.