ROGER TECHNOLOGY R93/RX2RC/U 2-Channel 433.92 MHz Rolling Code Radio Receiver

Introduction

This manual provides detailed instructions for the installation, setup, and operation of the ROGER TECHNOLOGY R93/RX2RC/U 2-Channel 433.92 MHz Rolling Code Radio Receiver. This device is designed to receive signals from compatible rolling code transmitters, enabling control of various automated systems. Please read this manual thoroughly before proceeding with installation or operation to ensure proper functionality and safety.

This image displays the ROGER TECHNOLOGY R93/RX2RC/U radio receiver. The device is shown with its black plastic casing partially open, revealing the green circuit board inside. The circuit board features various electronic components, including capacitors and connection terminals. The separate part of the casing is also visible, indicating how the unit is enclosed.

Safety Information

• Installation and maintenance must be performed by qualified personnel only.
• Disconnect power before performing any wiring or maintenance.
• Ensure all electrical connections comply with local regulations and standards.
• Do not expose the receiver to moisture, extreme temperatures, or corrosive substances.
• Keep the device away from children and unauthorized individuals.
• Use only original spare parts and accessories.

Package Contents

Verify that all components are present and undamaged upon unpacking:

• 1 x ROGER TECHNOLOGY R93/RX2RC/U 2-Channel Radio Receiver
• 1 x Plastic Casing
• 1 x Instruction Manual (this document)

Setup

1. Mounting the Receiver

1. Choose a suitable location for the receiver, ensuring it is protected from environmental elements and within optimal range of the transmitters.
2. Open the plastic casing carefully.
3. Secure the receiver base to a flat surface using appropriate screws (not supplied).
4. Ensure proper ventilation around the unit.

2. Wiring Connections

Refer to the wiring diagram printed on the circuit board or in the detailed technical documentation for specific connections. General connections include:

• Power Supply: Connect the appropriate voltage (e.g., 12/24V AC/DC) to the designated power input terminals. Observe polarity if DC.
• Antenna: Connect a 433.92 MHz antenna to the antenna input terminal for optimal range.
• Output Channels: Connect the control wires for the devices you wish to operate (e.g., gate opener, light) to the respective output terminals (Channel 1, Channel 2). These are typically relay outputs.

3. Programming Transmitters (Rolling Code)

The R93/RX2RC/U receiver uses rolling code technology for enhanced security. Follow these steps to program a new transmitter:

1. Press and hold the programming button on the receiver (often labeled 'PROG' or 'LEARN') for approximately 2-3 seconds until an LED indicator lights up or flashes.
2. Within 10 seconds, press the desired button on your rolling code transmitter. The receiver's LED should change its state (e.g., flash faster, turn solid) to indicate successful learning.
3. Repeat for additional transmitters or buttons if necessary.
4. Wait for the receiver's LED to turn off automatically, or press the programming button briefly to exit programming mode.
5. Test the programmed transmitter to ensure it activates the desired output channel.

Operating

Once the receiver is installed and transmitters are programmed, operation is straightforward:

• Press the corresponding button on your programmed rolling code transmitter.
• The receiver will detect the signal and activate the associated output channel.
• The activated output will control the connected device (e.g., open/close a gate, turn on/off a light).

Maintenance

The R93/RX2RC/U receiver requires minimal maintenance:

• Regular Inspection: Periodically check the receiver and its wiring for any signs of damage, wear, or loose connections.
• Cleaning: If necessary, gently clean the exterior of the plastic casing with a soft, dry cloth. Do not use abrasive cleaners or solvents.
• Antenna Check: Ensure the antenna is securely connected and free from obstructions for optimal signal reception.

Troubleshooting

Specifications

• Model: R93/RX2RC/U
• Brand: ROGER TECHNOLOGY
• Frequency: 433.92 MHz
• Channels: 2
• Code Type: Rolling Code
• Material: Plastic Casing
• Power Supply: (Typically 12/24V AC/DC - consult product label for exact voltage)
• Special Function: Variable code security, intelligent connectivity

Warranty and Support

For warranty information, please refer to the terms and conditions provided at the time of purchase or contact your retailer. If you encounter any issues not covered in this manual or require technical assistance, please contact ROGER TECHNOLOGY customer support or your authorized dealer.