Introduction
This manual provides instructions for the proper installation, use, and maintenance of your HJC HJ-26 Anti-Fog Tear-Off Pin Prepared Clear Helmet Shield. This shield is designed for use with HJC RPHA-11 Pro helmets.
A clear HJC HJ-26 helmet shield, designed for optimal visibility and prepared for anti-fog inserts and tear-offs.
Compatibility
The HJC HJ-26 helmet shield is specifically designed to fit HJC RPHA-11 Pro helmet models. Ensure your helmet is an RPHA-11 Pro before attempting installation.
Setup and Installation
Follow these steps to correctly install the HJ-26 shield onto your HJC RPHA-11 Pro helmet.
- Preparation: Ensure your helmet is clean and free of debris around the shield mechanism.
- Remove Old Shield (if applicable): Open the existing shield fully. Locate the release levers or buttons on both sides of the helmet's shield mechanism. Press or slide these to detach the old shield. Refer to your helmet's specific manual for detailed removal instructions.
- Align New Shield: Align the pivot points of the HJ-26 shield with the helmet's shield mechanism. Ensure the shield is oriented correctly (the anti-fog pinlock pins should be on the inside surface).
- Attach Shield: Press the shield firmly into place until you hear a click on both sides, indicating it is securely latched. Gently move the shield up and down to confirm it is properly installed and operates smoothly.
- Check Seal: Close the shield completely and check for a proper seal against the helmet's eyeport gasket.
Pinlock Insert (Sold Separately): If installing a Pinlock anti-fog insert, follow the instructions provided with the Pinlock product. The HJ-26 shield is prepared with pins for this purpose.
Tear-Offs (Sold Separately): The shield is also prepared for tear-offs. Align the tear-off with the external pins and secure it.
Operating Instructions
Opening and Closing: The shield can be opened and closed manually. It features multiple detent positions for airflow control.
Anti-Fog Function (with Pinlock insert): When a Pinlock insert is installed, it creates an insulating air pocket between the shield and the insert, preventing fogging. Ensure the Pinlock insert is clean and properly seated for optimal performance.
Tear-Off Function: Tear-offs are used to quickly clear the rider's vision of dirt or debris during riding. Simply pull the tab to remove the outermost layer.
Maintenance and Care
Proper care extends the life and maintains the clarity of your shield.
- Cleaning: Use only mild soap and lukewarm water with a soft, lint-free cloth. Avoid abrasive cleaners, solvents, or ammonia-based products, as these can damage the shield's coating.
- Drying: Air dry or gently pat dry with a clean, soft cloth. Do not wipe vigorously when wet, as this can scratch the surface.
- Storage: Store the helmet with the shield closed to prevent dust accumulation and scratches. Avoid prolonged exposure to direct sunlight or extreme temperatures when not in use.
- Inspection: Regularly inspect the shield for scratches, cracks, or damage. Replace the shield if visibility is compromised.
- Pinlock Insert Care: If a Pinlock insert is installed, remove it carefully for cleaning. Clean the Pinlock insert separately with mild soap and water, and allow it to air dry completely before re-installing. Avoid touching the silicone seal.
Troubleshooting
- Issue: Shield does not close properly or rattles.
- Solution: Ensure the shield is correctly installed on both pivot mechanisms. Check for any debris obstructing the mechanism.
- Issue: Excessive fogging (with Pinlock insert).
- Solution: Verify the Pinlock insert is clean and properly sealed against the main shield. The silicone bead should be making full contact. If the Pinlock is old, its anti-fog properties may diminish over time, requiring replacement.
- Issue: Scratches or reduced clarity.
- Solution: Scratches are typically permanent. Replace the shield if visibility is significantly impaired. Always use soft materials for cleaning.
Specifications
| Feature | Detail |
|---|---|
| Model | HJ-26 |
| Part Number | HHJ26G3003100 |
| Compatibility | HJC RPHA-11 Pro Helmets |
| Type | Anti-Fog Tear-Off Pin Prepared Clear Shield |
| Material | Polycarbonate |
| Item Weight | Approximately 0.71 lbs (11.4 oz) |
| Product Dimensions | 8 x 7 x 8 inches (packaging) |
Warranty Information
HJC products are manufactured to high standards. This shield is covered by a limited warranty against manufacturing defects. For specific warranty terms and conditions, please refer to the official HJC website or contact HJC customer support. Keep your proof of purchase.
Customer Support
For further assistance, technical support, or inquiries regarding your HJC HJ-26 helmet shield, please visit the official HJC website or contact their customer service department.
(Contact details may vary by region. Please check the website for local support information.)
